A switching power amplifier (SPA) provides the driving current for an active magnetic bearing (AMB) to achieve magnetic suspension (MS) control. The performances of the current bandwidth and current ripple should be significantly considered in the SPA of the AMB. The SPA can obtain a wide bandwidth by increasing the dc-link voltage. However, a high dc-link voltage will cause a high current ripple. To achieve a wide bandwidth and low current ripple, a new GaN-device-based SPA for the AMB of a flywheel energy storage system (FESS) is proposed in this article. The GaN SPA can operate at a high switching frequency and high dc-link voltage. Thus, the GaN SPA can improve the performance of the current bandwidth and current ripple compared to the conventional SPA. According to the characteristics of the GaN SPA, a low-loss PWM method and an optimal dead time strategy is proposed to increase the efficiency of the SPA. Furthermore, a high-response control approach of dead-beat model predictive control is proposed to further improve the current bandwidth. The proposed GaN SPA is applied in a 500-kW MS FESS prototype. The effectiveness of the SPA is verified experimentally.
27 September 2023 in IEEE Robotics and Automation Letters
This letter presents a novel tilt-rotor octocopter that can generate tiltable thrust without the need for servo-driven mechanisms. The octocopter's eight rotors are divided into pairs and each pair is mounted on an arm, which is connected to the airframe through passive hinges. Each pair is also equipped with a sub-controller that uses the differential thrust of the rotor pair to control the arm's tilting angle. Then, these sub-controllers work together with the main controller installed on the frame body to regulate the attitude and position of the octocopter. This octocopter can be controlled via a remote controller in a manner similar to a classic quadrotor, operating in stabilized or position mode both indoors and outdoors, also capable of executing flight missions following predefined trajectories. Considering that the communication delays between the main controller and sub-controllers would degrade the control performance due to the delayed response of the vectored thrust. We also propose a decentralized control allocation strategy that directly assigns parts of control loops to the sub-controllers so that the communication delays can be bypassed. Finally, we demonstrate the advantages of the new octocopter with the proposed method through simulations and real flight experiments.
Distributed electric propulsion technology has great potential and advantages in the development of drones. In this paper, to study the slipstream effect of distributed propellers, the actuator disk method was used to verify a single propeller, and the calculated thrust was in good agreement with the test results. Then, based on the actuator disk method, the influence of different installation positions on the slipstream effect was studied, and the distributed propeller layout was optimized by a genetic algorithm to improve the low-speed performance of the unmanned aerial vehicle (UAV) during the take-off phase and increase the cruise duration. The analysis results showed that the lift of the wing will be larger when the propellers are higher than the wing. The wing lift and drag of the counter-rotating are less than those of the co-rotating. Compared with the original layout, the lift coefficient of the optimized distributed propeller layout is significantly increased by 30.97%, while the lift/drag ratio is increased by 7.34%. Finally, we designed the test platform and qualitatively verified the calculated results without quantitative verification.
The composite material flywheel rotor of a flywheel energy storage system (FESS) has a low natural frequency. When the system suffers from noise interference, the magnetic bearing generates a force with the same frequency as the natural frequency and causes vibration to occur. Thus, it is necessary to suppress the natural vibration of the magnetic suspended (MS) FESS. The LMS adaptive notch filter is generally adopted for vibration suppression. The vibration suppression performance of the system is different when the insertion position of the notch filter is different. This paper analyzes the influence of the notch filter in different insertion positions of the control system. Through the transfer function from noise to magnetic bearing force, theoretical analysis of the influence of different positions of the notch filter is performed. Corresponding experiments are performed in a 500 kW MS FESS prototype. The theoretical analysis is verified experimentally.
Fixed-wing Vertical Takeoff and Landing (VTOL) drones have been widely researched and applied because they combine the advantages of both rotorcraft and fixed-wing drones. However, the research on the transition mode of this type of drone has mainly focused on completing the process quickly and stably, and the application potential of this mode has not been given much attention. The objective of this paper is to routinize the transition mode of compound VTOL drones, i.e., this mode works continuously for a longer period of time as a third commonly used mode besides multi-rotor and fixed-wing modes, which is referred to as the hybrid mode. For this purpose, we perform detailed dynamics modeling of the drone in this mode and use saturated PID controllers to control the altitude, velocity, and attitude of the drone. In addition, for more stable altitude control in hybrid mode, we identify the relevant parameters for the lift of the fixed-wings and the thrust of the actuators. Simulation and experimental results show that the designed control method can effectively control the compound VTOL drone in hybrid mode. Moreover, it is proven that flight in hybrid mode can reduce the flight energy consumption to some extent.