Today, a promising research area is the study of the behavior of the materials’ technological and physical characteristics under the external energy effects, such as constant magnetic fields. It is caused by the emergence of multifactorial scientific and industrial problems arising because of the introduction of high technologies into production. One of the directions is the production of new equipment, devices, and machines that somehow form electromagnetic fields around them. Therefore, an umbrella approach to studying the influence of magnetic field effects on the deformation characteristics of metals and alloys contributes to a deeper understanding of the physical nature of this effect. As an object for the research, the authors selected commercially pure titanium of VT1-0 grade. The work aims to study the influence of a constant magnetic field of 0.3 T on microhardness, creep rate, and fracture surface of commercially pure VT1-0 titanium. The results show that under the influence of a constant magnetic field of 0.3 T, the relative value of VT1-0 titanium microhardness decreases by 2–5 %, followed by relaxation to the initial value. The creep rate of titanium increases by approximately 31 % when applying a field of 0.3 T induction during the test (without field applying, the creep rate is 2.4 %/h, in the magnetic field is 3 %/h). The fracture surface analysis using scanning electron microscopy (SEM) shows that titanium specimens undergo ductile fracture. Numerous equiaxial destruction pits characterize the fracture surface. It should be noted that pits with the stretched areas are present mainly on the samples destroyed under the creep conditions in a constant magnetic field of 0.3 T.
Mechanical tests of commercially pure lead grade C2 were carried out, cylindrical samples of lead were destroyed in the process of creep with a constant tensile force. The tests were carried out initially without the inclusion of a magnetic field during deformation, then with the inclusion of a magnetic field with an induction of 0.5 T. Based on the data obtained, characteristic curves of the creep process were constructed. A change in the nature of the curve is revealed. At the discovered linear stage of the process, the creep rate was calculated. A decrease in the creep rate is shown compared to the process without the action of an external magnetic field. The duration of the creep process is analyzed depending on the induction and the percentage of residual relative elongation of the samples. Analysis of the fractograms showed a difference in the morphology of fractures in the studied samples. With the use of a magnetic field during the destruction of the sample, the number of pits on the surface decreased, the fibrous zone increased, and the fracture morphology changed.
12 December 2022 in Journal of Surface Investigation: X-Ray, Synchrotron and Neutron Techniques
The surface layer of AK5M2 alloy is modified with a Ti film by the vacuum-arc method. The modified samples are irradiated by the method of electron-beam processing using five modes. The dependences of the crystal-lattice parameter and the phase composition of samples of the AK5M2 alloy with surface-modified Ti alloy on the beam energy density during electron-beam processing are determined. The defect substructure of the samples is studied by scanning electron microscopy. The dependence of the coating thickness on the energy density of the electron beam is revealed. The modes are determined, in which the electron-beam energy density is insufficient for the formation of a homogeneous coating. The most rational mode of electron-beam processing is established, in which a homogeneous layer with the least number of surface defects is formed.
14 September 2023 in Izvestiya of Altai State University
Проведены измерения микротвердости образцов технически чистого свинца без воздействия и при воздействии внешнего магнитного поля с индукцией 0.3 Тл, 0.4 Тл, 0.5 Тл. Получены зависимости микротвердости поверхности свинца марки С2 от времени выдержки в магнитном поле, отражающие влияние магнитного поля на пластические характеристики свинца. Выявлено время выдержки, при котором наблюдается максимальный эффект влияния на микротвердость. Дополнительно были проведены испытания на микротвердость образцов технически чистого свинца без воздействия и при воздействии внешнего магнитного поля с индукцией до 0.3, 0.4 и 0.5 Тл и временем обработки 0.25, 0.5 и 1 час. По полученным данным микротвердости вычислен параметр пластичности свинца в исходном состоянии и после обработки во внешнем магнитном поле, показаны зависимости параметра пластичности от времени обработки. Установлен характер изменения параметра пластичности при обработке свинца в магнитном поле с индукцией до 0.5 Тл. Показаны проценты изменения значений микротвердости в зависимости от индукции магнитного поля.
1 September 2022 in Metal Science and Heat Treatment
The modification of metals and alloys by the external energy deposition methods makes it possible to locally strengthen the surface layer of parts and assemblies made of aluminum alloys. This study is aimed at revealing the regularities of the effect of electron beam processing modes on the mechanical characteristics and fracture surface morphology of the Ti-surface-modified AK5M2 alloy. The authors used the methods of modern physical materials science. The surface of the AK5M2 alloy was modified with a Ti film by the vacuum arc method. The modified samples of the AK5M2 alloy were irradiated with an intense pulsed electron beam in modes differing in the energy density of the electron beam (from 10 to 50 J/cm2). Mechanical tests were carried out by uniaxial tension to fracture of the alloy samples in the original state and the modified samples before and after the irradiation in five modes. Using scanning electron microscopy, the authors carried out a fractographic analysis of the fracture surface of the samples obtained as a result of tension. The development of a unique method for modifying the AK5M2 alloy makes it possible to improve its strength and morphological properties compared to the material in its original state. As a result of the mechanical tests, the authors determined the values of yield strength, ultimate tensile strength, and relative residual elongation and narrowing at fracture. The dependence between the change in the deformation characteristics and the structure of the fracture surface on the electron-beam processing modes was established. On the basis of the tests performed on the samples of the Ti-surface-modified AK5M2 alloy, the authors revealed a mode of electron-beam processing leading to the formation of a surface structure characterized by higher mechanical properties. The Ti surface modification of the AK5M2 alloy after electron-beam processing in a mode using an electron beam energy density of 30 J/cm2 results in an increase in the strength characteristics. The parameters of this mode can be used for local hardening of parts made of this alloy, for example, bush bearings.