We study the voltage control of perpendicular magnetic anisotropy in an ultrathin Fe layer sandwiched between the Cr buffer and MgO tunneling barrier layers. A high-interface magnetic anisotropy energy of is achieved in the Cr/ultrathin structure. A large voltage-induced perpendicular magnetic anisotropy change is observed under the negative-bias voltage applications for the case of the Fe layer thinner than 0.6 nm. The amplitude of the voltage-induced anisotropy energy change exhibits a strong Fe-thickness dependence and it reaches as high as . The observed high values of the surface anisotropy and voltage-induced anisotropy energy change demonstrate the feasibility of voltage-driven spintronic devices.
Voltage control of spin enables both a zero standby power and ultralow active power consumption in spintronic devices, such as magnetoresistive random-access memory devices. A practical approach to achieve voltage control is the electrical modulation of the spin–orbit interaction at the interface between 3d-transition-ferromagnetic-metal and dielectric layers in a magnetic tunnel junction (MTJ). However, we need to initiate a new guideline for materials design to improve both the voltage-controlled magnetic anisotropy (VCMA) and perpendicular magnetic anisotropy (PMA). Here we report that atomic-scale doping of iridium in an ultrathin Fe layer is highly effective to improving these properties in Fe/MgO-based MTJs. A large interfacial PMA energy, Ki,0, of up to 3.7 mJ m−2 was obtained, which was 1.8 times greater than that of the pure Fe/MgO interface. Moreover, iridium doping yielded a huge VCMA coefficient (up to 320 fJ Vm−1) as well as high-speed response. First-principles calculations revealed that Ir atoms dispersed within the Fe layer play a considerable role in enhancing Ki,0 and the VCMA coefficient. These results demonstrate the efficacy of heavy-metal doping in ferromagnetic layers as an advanced approach to develop high-density voltage-driven spintronic devices.
1 April 2021 in Nuclear Instruments and Methods in Physics Research Section B: Beam Interactions with Materials and Atoms
Recently, perpendicular magnetic anisotropy (PMA) and its voltage control (VC) was demonstrated for Cr/Fe/MgO. In this study, we shed light on the origin of large voltage-induced anisotropy change in Cr/Fe/MgO. Analysis of the chemical structure of Cr/Fe/MgO revealed the existence of Cr atoms in the proximity of the Fe/MgO interface, which can affect both magnetic anisotropy (MA) and its VC. We showed that PMA and its VC can be enhanced by controlled Cr doping at the Fe/MgO interface. For Cr/Fe (5.9 Å)/Cr (0.7 Å)/MgO with an effective PMA of 0.8 MJ/m3, a maximum value of the voltage-controlled magnetic anisotropy (VCMA) effect of 370 fJ/Vm was demonstrated due to Cr insertion.
An in-plane spin-reorientation transition occurring during the growth of epitaxial Fe films on W(110) was studied in~situ by using the nuclear resonant scattering of synchrotron radiation. The spin-reorientation transition originates at the Fe/W(110) interface and proceeds via a noncollinear spin structure resembling a planar domain wall that propagates towards the surface with increasing film thickness.
A comparative study of the structure and magnetism of Fe/CoO(111) and Fe/CoO(001) epitaxial bilayers was performed to investigate the role of uncompensated spins in the exchange bias (EB) phenomenon. Low-energy electron diffraction, x-ray photoelectron spectroscopy, conversion electron Mössbauer spectroscopy (CEMS), and the magneto-optic Kerr effect were used to characterize the structural and magnetic properties of the bilayers. Magnetically compensated and uncompensated CoO films were prepared using molecular beam epitaxy through the evaporation of single Co atomic layers and their subsequent oxidation (layer-by-layer technique) on MgO crystals with (001) and (111) orientations. Two-monolayer-thick Fe probes located on top of the oxide films and covered with Fe allowed for an analysis of the interfacial chemical and magnetic structure using CEMS. For both structures, submonolayer oxidation of the iron detected at the Fe/CoO interface was found to be accompanied by the formation of a mixed FeCo region. The Fe layers showed fourfold magnetocrystalline anisotropy when grown on CoO(001) and weak uniaxial anisotropy when grown on CoO(111). Although the structural quality and composition of the two structures were comparable, they exhibited distinct EB properties. A hysteresis loop shift as high as 354 Oe at 80 K was obtained for the Fe/CoO(111) bilayer, compared to only 37 Oe for the magnetically compensated Fe/CoO(001).