21 February 2018 in Biomedical Optics Express
Low-power laser irradiation of red light has been recognized as a promising tool across a vast variety of biomedical applications. However, deep understanding of the molecular mechanisms behind laser-induced cellular effects remains a significant challenge. Here, we investigated mechanisms involved in the death process in human hepatic cell line Huh7 at a laser irradiation. We decoupled distinct cell death pathways targeted by laser irradiations of different powers. Our data demonstrate that high dose laser irradiation exhibited the highest levels of total reactive oxygen species production, leading to cyclophilin D-related necrosis via the mitochondrial permeability transition. On the contrary, low dose laser irradiation resulted in the nuclear accumulation of superoxide and apoptosis execution. Our findings offer a novel insight into laser-induced cellular responses, and reveal distinct cell death pathways triggered by laser irradiation. The observed link between mitochondria depolarization and triggering ROS could be a fundamental phenomenon in laser-induced cellular responses.
17 March 2014 in Advances in Optical Technologies
The dependence of the dynamic range of the phase generated carrier (PGC) technique on low-pass filters passbands is investigated using a simulation model. A nonlinear character of this dependence, which could lead to dynamic range limitations or measurement uncertainty, is presented for the first time. A detailed theoretical analysis is provided to verify the simulation results and these results are consistent with performed calculations. The method for the calculation of low-pass filters passbands according to the required dynamic range upper limit is proposed.
15 February 2020 in Optical and Quantum Electronics
1 October 2024 in Journal of Optical Technology
Subject of study. Cascaded high-signal-attenuation narrowband fiber Bragg gratings connected via a fiber-optic isolator. Aim of study. This study aims to develop a narrowband (82-pm bandpass) spectral filter based on cascaded fiber Bragg gratings. Method. Long, narrow-bandwidth fiber Bragg gratings were written using a phase mask and a scanning beam from a Coherent COMPexPRo 102F krypton fluoride (KrF) excimer laser. Two gratings with identical central Bragg resonance wavelengths were cascaded via a fiber-optic isolator in order to avoid interference effects. Main results. Transmission spectra from the resulting fiber-Bragg-grating cascade had a measured 3-dB filter transmission bandwidth of 82 pm and a maximum attenuation of 46 dB. The filter had a central minimum-transmission wavelength of 1549.9 nm. For comparison, single gratings of the same length with similar attenuation value have a 3-dB bandwidth of 123 pm—much larger than that of the cascaded fiber Bragg grating filter. Practical significance. The narrowband filter based on cascaded fiber Bragg gratings obtained in this paper is suitable for separating carrier wavelengths from subcarrier wavelengths in subcarrier-wave quantum key distribution systems and for use in other communications-link applications requiring selection of a narrow spectral band.
1 March 2025 in Journal of Optical Technology
Subject of study. The subject of this study is the analysis of the parameters and optical characteristics of a distributed feedback (DFB) laser based on a single fiber Bragg grating (FBG) with a constant period inscribed in an erbium-doped optical fiber. Aim of study. The aim was to determine the dependence of the radiation generation mode of a DFB laser, based on a single FBG with a constant period recorded using the phase mask method, on the pump power and resonator length. Method. FBGs were inscribed using the phase mask method via optical beam translation of a KrF excimer laser with a central wavelength of 248 nm. Structures with lengths ranging from 40 mm to 70 mm (in 5 mm steps) and reflection coefficients exceeding 99% were recorded in a FiberCore I-25(980/125) optical fiber under low-temperature hydrogen loading. A pump diode, with a central wavelength and maximum output of 980 nm and 435 mW, respectively, was used. The correlations between the radiation parameters and variations in the FBG length and pump power were measured. Main results. The variations in the generation mode of the DFB laser on pump and resonator parameters were analyzed. The results showed that stable radiation can be generated, at pump powers up to 435 mW, using a single 45-mm-long FBG with a constant period (recorded using the phase mask method in an erbium-doped fiber), without requiring π -phase-shifted structures or longer gratings (recorded using the step-by-step method). Practical significance. The results obtained can be applied to simplify optical schemes and optimize the performance of measurement systems based on DFB fiber lasers.
1 December 2024 in Scientific and Technical Journal of Information Technologies, Mechanics and Optics
Weight sensors are widely used in the freight transportation industry. In the systems for weighing vehicles while moving, ceramic, polymer, quartz piezoelectric sensors, load or hydraulic cells, strain gauges are used as sensitive elements. However, most electric sensors are susceptible to electromagnetic interference. Currently, fiber-optic sensors are most actively developed and put into operation due to their relatively low cost, small weight and size parameters, high measurement accuracy and complete passivity to electromagnetic disturbances. Fiber-optic sensors are most often implemented using fiber Bragg gratings, taking into account the convenience of their multiplexing. Mechanical deformations lead to a shift in the wavelength of the Bragg resonance of the grating. At the same time, the problem of using fiber gratings is associated with their sensitivity to temperature. To achieve high accuracy in measuring the deformation value, and accordingly, the weight characteristics of the object, it is necessary to eliminate or compensate for the effect of the sensor temperature on its readings. Most modern studies describe sensors that either operate in laboratory conditions or involve the use of an additional sensor that complicates the circuit for measuring temperature. The paper proposes a method for solving the problem of cross-sensitivity of a fiber diffraction structure to temperature and deformation. The method is based on the use of a pair of closely spaced gratings in the sensitive element of the sensor. One of the gratings has a constant period along the length, and the other has a variable one. The design of the sensitive element ensures the transfer of mechanical load only to the fiber grating with a constant period, and the temperature change equally affects both diffraction structures. A design solution for the sensitive element is proposed that allows for temperature effects compensation without using additional elements. A mathematical model of temperature effects is presented, allowing estimating the dependence of the temperature gradient on time for different thicknesses of the sensitive element. Modeling has showed that for a sample 0.95 cm thick, the temperature gradient inside the substrate is insignificant. With a sharp change in temperature, the equalization of the temperature field within the substrate at a level of 90 % occurs in no more than 2.5 s. The mechanical load on the sensitive element can pass relative to the fiber grating at different angles in connection with which the value of the shift of the central wavelength of the Bragg resonance was studied in detail depending on the point of application and direction of the load. The proposed technology may be of interest in the development and operation of automatic weight and size control systems with temperature compensation without the use of additional sensors. The proposed system is easy to operate and it has a low cost.