With the continuous advancement of technology, numerous areas of research are dedicated to the development of innovative materials. The focus is not only on creating financially viable options but also on producing materials that exhibit superior performance compared to those currently in use. Alongside this drive for innovation, there is a growing concern for sustainability, making it crucial for new technological developments to adopt processes that minimize environmental impact while promoting ecological preservation. In this context, this study focuses on evaluating the mechanical properties of a composite material through various tests, including the tensile test, Shore-D hardness test, and impulse excitation test. The composite material in question was formulated in three distinct compositions, incorporating glass powder with a particle size exceeding 325 mesh as a reinforcing filler. This glass powder is sourced from discarded glass bottles, thus contributing to waste reduction and promoting recycling. The composite material studied consists of an epoxy resin matrix, with glass particles acting as reinforcing fillers in varying proportions of 5%, 10%, and 20%. The specimens used for mechanical testing were fabricated using an open mold technique. Overall, the results obtained in the mechanical tests indicate an improvement in the main properties such as the modulus of elasticity, tensile strength, breaking stress, toughness and hardness of the material. However, the study also reveals that beyond a certain composition limit, there is no significant improvement and, in some cases, a slight decline in these properties is observed. This suggests the existence of an ideal composition where the balance between mechanical performance and material composition is achieved.
17 October 2026 in Journal of Applied Polymer Science
Reducing zinc content in rubber formulations remains an important challenge due to environmental concerns associated with the use of zinc oxide (ZnO) as part of vulcanization systems. Zinc‐containing layered double hydroxides (Zn/Al‐LDHs) offer an alternative approach to incorporating zinc into lamellar structure and have been investigated as both vulcanization activators and fillers. However, the curing behavior of unmodified Zn/Al‐NO 3 LDH in conventional nitrile rubber (NBR) remains insufficiently understood. In this study, Zn/Al‐NO 3 LDH was evaluated as an alternative low‐zinc vulcanization activator for nitrile rubber (NBR) as a replacement for the ZnO/stearic acid system. Conventional (A/S = 0.6) and efficient (A/S = 3.0) sulfur‐curing systems were compared. In the conventional system, the LDH decreased the apparent Ea from 90.81 to 70.95 kJ.mol −1 and reduced the pre‐exponential factor by approximately two orders of magnitude. Tensile strength remained comparable, whereas tear strength decreased by approximately 14%. Thermogravimetric analysis showed a slight increase in the onset degradation temperature for the LDH‐containing formulations. Based on nominal compositions, replacing the ZnO/stearic acid activation system with Zn/Al‐NO 3 LDH corresponded to an estimated 71% reduction in zinc loading. Environmental benefits cannot be inferred from this reduction because zinc release, bioavailability, and ecotoxicological effects were not evaluated.
Biodegradable polylactic acid (PLA) and poly(butylene adipate-co-terephthalate) (PBAT) blends can mitigate plastic pollution. This study demonstrates that agro-industrial co-products can directly functionalize these blends without requiring intensive isolation steps. PLA/PBAT films incorporated with mango seed components were prepared via solvent casting. Fourier-transform infrared spectroscopy (FTIR) confirmed the chemical signatures of all constituent phases, identifying key characteristic bands such as carbonyl stretching at 1710 cm−1, cellulose at 2917 cm−1, and amide II at 1535 cm−1. Scanning electron microscopy (SEM) revealed a phase-separated matrix morphology, alongside starch granules and cellulose fibers from the raw fillers. Statistical analysis demonstrated that mango seed incorporation preserved the matrix mechanical stability (p > 0.05), with biocomposite puncture strength values (1.12 to 1.69 MPa) remaining statistically comparable to the neat blend (1.89 MPa), indicating potential for packaging applications. The fillers accelerated soil degradation; during a seven-week period, the composite with mango kernel (PLA/PBAT-K) exhibited the highest weight loss of 5.15% compared to 2.32% for the neat blend. These findings demonstrate the viability of incorporating agricultural co-products into PLA/PBAT matrices, providing a structural baseline for future biomass valorization studies.
Population growth demands new sustainable food sources and edible insects, such as black soldier fly larvae, stand out due to their high biological value. Entomophobia requires transformation processes to improve consumer acceptance, with the production of protein concentrates as a viable alternative. Therefore, methods that enhance both yield and efficiency in protein extraction are essential. Wet fractionation is a promising alternative to optimize extraction while preserving the compounds’ properties. In this context, this study produced a protein concentrate from the liquid fraction extracted from the larvae, characterizing its centesimal composition, techno-functional properties, and structural characteristics. The liquid fraction obtained through an oil press machine, underwent manual and chemical defatting (with hexane), followed by alkaline solubilization and acid precipitation. The protein content of the whole-larvae flour was 28.8% and reached 67.6% in the concentrate, demonstrating satisfactory extraction efficiency. Water and oil retention capacities were higher in the concentrate than in the defatted flour. The foaming and emulsifying capacities were also higher in the concentrate, although foam stability was greater in the defatted flour. Solubility was higher at extreme pH levels (2 and 12) and lower at pH 4 and 5, which corresponded to the isoelectric point as confirmed by zeta potential measurements. Furthermore, changes in functional groups and microstructure were observed, which are essential for improving extraction processes. Therefore, these results highlighted the feasibility of a sustainable process for the production of protein concentrates from the black soldier fly larvae.