Himadri Raha

Himadri Raha

Auto-generated profile, based on publicly available information

Himadri Raha

School of Nano Science and Technology, Indian Institute of Technology Kharagpur-721302, India

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
8 September 2021 in ACS Sensors
Verified
Journal Article
Closed access
DBDebasree Burman
Debasree Burman
HRHimadri Raha
Himadri Raha
BMBibhas Manna
Bibhas Manna
PPPanchanan Pramanik
Panchanan Pramanik
PGPrasanta Kumar Guha
Prasanta Kumar Guha

25 January 2023 in Journal of Electroanalytical Chemistry
Verified
Journal Article
Closed access
HRHimadri Raha
Himadri Raha
DPDebabrata Pradhan
Debabrata Pradhan
PGPrasanta Kumar Guha
Prasanta Kumar Guha

1 April 2022 in Nanotechnology
Verified
Journal Article
Closed access
HRHimadri Raha
Himadri Raha
DPDebabrata Pradhan
Debabrata Pradhan
PGPrasanta Kumar Guha
Prasanta Kumar Guha
Rapidly changing demand on energy storage systems makes it essential to redesign the device architecture and materials required to fabricate the devices. It is crucial to introduce capacitive behaviour in a conventional energy storage device (batteries) to improve the lifetime and power efficiency of the hole energy storage system. The charge storing nature of electrode material primarily depends on particle size, grain size, the electrode’s chemical structure, and effective diffusion lengths for electrolytes within the electrode. Here V 2 O 5 based Li-ion battery electrode is transformed into a Li-ion pseudocapacitive electrode by structural modifications. The modified structures are achieved by optimizing reaction pressure to obtain larger, medium and smaller V 2 O 5 particles (namely, V 2 O 5 -L, V 2 O 5 -M and V 2 O 5 -S). As a result, the plateau regions in galvanostatic charge–discharge plots and highly intense redox peaks in the CV plots of V 2 O 5 -L get flattened for V 2 O 5 -S. Also, the lucrative improvement in rate capabilities and stability for V 2 O 5 -S indicates induced pseudocapacitance in V 2 O 5 . Some devices are fabricated with the extrinsic pseudocapacitive material (V 2 O 5 -S), providing 4.36 mWh cm −3 volumetric energy density with 125 mW cm −3 volumetric power density. The device retains around 95% of its initial capacitance after 10k cycles and holds up to 63% after 25k stability cycles.

12 August 2019 in Nanotechnology
Verified
Journal Article
Closed access
HRHimadri Raha
Himadri Raha
BMBibhas Manna
Bibhas Manna
DPDebabrata Pradhan
Debabrata Pradhan
PGPrasanta Kumar Guha
Prasanta Kumar Guha
A forest like 3D carbon structure formed by reduced graphene oxide (RGO) was prepared to use as an electrode material for a highly power efficient supercapacitor. To improve the specific energy of the electrode, pore like defects were incorporated on the RGO forests by atomic oxygen etching, during the UV-ozone treatment. The modified surface helps to increase the net capacitance by permitting the electrolyte to the inner core of the active material and improving the minimal quantum capacitance. Density functional theory based first principle studies were carried out to find DOS at the Fermi level of defect induced RGO sheet and hence to validate the effect of quantum capacitance on net capacitance. Specific capacitance of RGO forest was increased by almost 150% after introduction of the defects. The best performing material exhibits 18.87 mF cm −2 areal capacitance at 2 mA cm −2 current density which is equivalent to 70 F cm −3 at 3.7 A cm −3 current density, and it was used to fabricate the supercapacitor. Two supercapacitors were fabricated, (i) on graphite sheet (non-flexible) and (ii) on scotch tape (flexible). Here PVA-KOH gel soaked filter paper was used as electrolyte-separator. Both the prepared supercapacitors on graphite sheet and scotch tape are able to transfer electrical energy with ultra high specific power (656.25 mW cm −3 and 164.06 mW cm −3 respectively) while maintaining moderate energy densities. The first device can withstand its primary capacitance by 90% even after 10 K charge–discharge cycles and the flexible device was able to hold 96% of its capacitance after 1 K bending cycles.

12 October 2018 in IEEE Transactions on Electron Devices
Verified
Journal Article
Closed access
BMBibhas Manna
Bibhas Manna
HRHimadri Raha
Himadri Raha
ICIndrajit Chakrabarti
Indrajit Chakrabarti
PGPrasanta Kumar Guha
Prasanta Kumar Guha
This paper presents a density functional theory-based first principle study to investigate the atomic-scale interactions of formaldehyde (H 2 CO) molecules with different oxygen containing functional groups of graphene oxide to identify which particular functional group possesses better adsorption capability toward H 2 CO molecule. The detailed study on formaldehyde adsorption has been conducted in terms of changes in structural, energetic, electronic, and transport properties of graphene oxides modeled with sp 3 hybridized hydroxyl (-OH) and epoxy (C-O-C) groups on the carbon basal plane. Our computational results suggest that the graphene oxidized with only -OH group shows the highest affinity toward formaldehyde as compared with epoxy oxidized graphene and graphene oxide containing both the functional groups. The influence of vacancy defect on improving the sensing response of graphene oxide has also been studied. The results of current–voltage ( ${I}$ – ${V}$ ) characteristics reveal that graphene oxidized with only hydroxyl group can achieve an improvement in sensitivity by almost two times and five times as compared with graphene oxide containing both the functional groups and the pristine graphene sheet, respectively. Moreover, the selectivity test for some common indoor air pollutants was also carried out and the test results suggest that H 2 CO molecule is highly selective toward the -OH group of graphene oxide as compared with the epoxy group.