6 October 2021 in IEEE Transactions on Power Electronics
Phase-locked loops (PLLs) and frequency-locked loops (FLLs) are of importance in power and energy applications. Both technologies have been introduced to speed-sensorless- controlled motor drives, and increasing applications of PLLs and FLLs for speed estimation are foreseen. To enable a proper and good design, a thorough review of the PLL- and FLL-based speed estimation schemes is then provided in this article. It is revealed through the review that many PLL- and FLL-based estimation schemes fail to accurately track a frequency ramp (i.e., obvious estimation errors appear), which may lead to a compromised estimation accuracy when these schemes that are applied in induction motor drives operating during acceleration and deceleration processes. To address this, the proven speed estimation schemes together with new attempts are also presented in this article. Moreover, various challenges to the PLL- and FLL-based speed estimation schemes, including harmonics, dc offsets, and parameter variations, are considered when evaluating these schemes. Solutions to tackle these disturbances are accordingly presented. In addition, two representative estimation schemes are exemplified through experimental tests. Finally, further challenges in using the PLL- and FLL-based schemes for speed estimation are discussed.
1 February 2022 in IEEE Transactions on Transportation Electrification
Speed-sensorless control of induction motor drives based on the extended state observer (ESO) attracts much popularity due to its key characteristics, e.g., satisfactory estimation performance, and high robustness against disturbances. However, the conventional ESO generally uses fixed high gains to achieve fast convergence. This may bring about the concern of noise sensitivity. Moreover, a proportional-integral (PI)-type speed controller is mostly adopted in speed-sensorless control of induction motor drives, which may cause unsatisfactory system dynamics. To address these, an adaptive active disturbance rejection control (ADRC) strategy is proposed for speed-sensorless induction motor drives in this article. In this scheme, a third-order adaptive ESO (AESO) is first used to estimate the speed, the phase, and the overall disturbance. Then, a speed controller based on the state error feedback control rate (SEFCR) is designed to improve system dynamics. In practice, disturbances like dc offsets may further challenge estimation performance, and hence, a closed-loop flux observer (CLFO) is employed to deal with this issue. Additionally, a parameter sensitivity analysis of the CLFO is also provided to evaluate the performance of the proposed scheme. Finally, extensive experimental tests have been carried out to validate the effectiveness of the proposed.
7 March 2022 in IEEE Transactions on Power Electronics
Active flux model of permanent magnet synchronous motors simplifies the model and eases sensorless control implementation. However, incorporating the current model (CM) that depends on the estimated electrical position for active flux estimation may cause performance degradation. The conventional active flux observer analysis revealed that position error influences sensorless control performance, especially during transient conditions. Thus, two improvement strategies named method-1 and method-2 are proposed in this article. Method-1 is based on an adaptive gain observer-based approach designed to discard the effect of position error. The observer gains are dependent on the estimated reference frame currents, which leads to the observer complexity. Method-2, on the other hand, uses the position error from the estimated active flux to obtain the true CM active flux without changing the conventional observer gains. Thus, the effect of position error on active flux estimation is discarded. Method-1 and method-2 fully decoupled the speed-position identification and the active flux observer. Meanwhile, a feedforward compensated phase-locked loop is adopted for speed-position identification. The proposed sensorless control strategies have been extensively validated using the Texas digital signal processor (TMS320F28335) and RT-LAB real-time simulator. The experimental results indicated that the proposed methods improved the sensorless control and active flux estimation performance.
17 October 2024 in IEEE Transactions on Power Electronics
In order to achieve high robustness and high-precision current control, this article proposes a disturbance correction observer based on repetitive control (RDCO) for deadbeat predictive current control (DPCC-RDCO) scheme of permanent magnet synchronous motor (PMSM). In this technology, the disturbance correction based on the disturbance estimation of the extended state observer is presented to enhance the observer robustness. Meanwhile, a repetitive controller is embedded into the disturbance correction term to improve the estimation accuracy of periodic harmonics. Furthermore, the estimation performance, parameter characteristics, and convergence stability of the proposed observer are theoretically analyzed. With the current disturbance and current prediction accurately estimated by the RDCO, the improved DPCC scheme based on the established predictive current model is developed. Compared with the basic schemes, the proposed DPCC-RDCO can effectively suppress current deviation, and achieve excellent dynamic tracking and robust performance. Finally, the effectiveness and superiority of the studied method are verified experimentally in PMSM drives under different operating conditions.
1 December 2022 in IEEE Transactions on Industrial Electronics
Extended sliding mode disturbance observer-based current observer for interior permanent magnet synchronous motors (IPMSM) is an efficient method, where the estimated dq -axis disturbances are linearly dependent on the position estimation error. Thus, this article proposed a robust speed-position identification strategy using the estimated disturbances. First, an analysis of the estimated disturbances concerning parameter variation, position estimation error, and the effect on the sensorless control performance is given. Then, a combined method that uses the dq -axis disturbances is proposed for speed-position identification. The proposed method is robust against stator resistance variation without estimating the stator resistance. However, the flux linkage variation effect sustains per the external load. Therefore, the permanent flux linkage variation electromotive force (EMF) compensator is included. The compensator is activated in the medium to the high-speed range while deactivated in the low-speed area. Thus, the advantage of the combined method for the low-speed area against resistance variation is kept. Various hardware-in-the-loop experimental studies and comparative analysis show that the proposed method with a permanent flux linkage variation back EMF compensator achieved an excellent sensorless control performance for IPMSM.
30 May 2023 in IEEE Transactions on Industrial Electronics
Offset error from the measured phase current mostly causes a performance afflicted for interior permanent-magnet synchronous motor (IPMSM) drives, and innovative solutions are eagerly sought. Considering this, this article proposes an adaptive extended state observer (AESO) to compensate the current measurement offset error (CMOE) without additional hardware. In the proposed scheme, the AESO is designed in a stationary coordinate system to estimate CMOE in dc form. Notably, the proposed AESO possesses a second-order low-pass filtering characteristics. With this, the proposed method shows a high robustness against the disturbances from the ac components caused by motor parameter changes, etc. Furthermore, the adaptive gains enable the proposed scheme to maintain a satisfactory performance under the motor frequency changes. The feasibility of the proposed scheme is thoroughly verified by extensive experimental tests based on the test bench of a 3-kW IPMSM drives.