Fawad Ali

Fawad Ali

Auto-generated profile, based on publicly available information

Fawad Ali

School of Chemistry, Physics and Mechanical Engineering Science and Engineering Faculty Queensland University of Technology 2 George Street Brisbane 4000 QLD Australia

Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
24 June 2019 in ACS Applied Energy Materials
Verified
Journal Article
Closed access
FAFawad Ali
Fawad Ali
NPNgoc Duy Pham
Ngoc Duy Pham
LFLijuan Fan
Lijuan Fan
VTVincent Tiong
Vincent Tiong
Kostya (Ken) OstrikovKostya (Ken) Ostrikov
Kostya (Ken) Ostrikov
TTTuquabo Tesfamichael
Tuquabo Tesfamichael

4 September 2018 in ChemSusChem
Verified
Journal Article
Closed access
PDF file
FAFawad Ali
Fawad Ali
NPNgoc Duy Pham
Ngoc Duy Pham
HBH. Jonathan Bradford
H. Jonathan Bradford
NKNima Khoshsirat
Nima Khoshsirat
KOKen Ostrikov
Ken Ostrikov
TTTuquabo Tesfamichael
Tuquabo Tesfamichael

23 August 2016 in ACS Applied Materials & Interfaces
Verified
Journal Article
Closed access
TQTengfei Qiu
Tengfei Qiu
Bin LuoBin Luo
Bin Luo
FAFawad Ali
Fawad Ali
EJEsa Jaatinen
Esa Jaatinen
Liang WangLiang Wang
Liang Wang
Hongxia WangHongxia Wang
Hongxia Wang

18 October 2018 in Beilstein Journal of Nanotechnology
Verified
Journal Article
Open access
PDF file
NKNima Khoshsirat
Nima Khoshsirat
FAFawad Ali
Fawad Ali
VTVincent Tiing Tiong
Vincent Tiing Tiong
MAMojtaba Amjadipour
Mojtaba Amjadipour
Hongxia WangHongxia Wang
Hongxia Wang
Nunzio MottaNunzio Motta
Nunzio Motta
Molybdenum (Mo) is the most commonly used material as back contact in thin-film solar cells. Adhesion of Mo film to soda–lime glass (SLG) substrate is crucial to the performance of solar cells. In this study, an optimized bilayer structure made of a thin layer of Mo on an ultra-thin chromium (Cr) adhesion layer is used as the back contact for a copper zinc tin sulfide (CZTS) thin-film solar cell on a SLG substrate. DC magnetron sputtering is used for deposition of Mo and Cr films. The conductivity of Mo/Cr bilayer films, their microstructure and surface morphology are studied at different deposition powers and working pressures. Good adhesion to the SLG substrate has been achieved by means of an ultra-thin Cr layer under the Mo layer. By optimizing the deposition conditions we achieved low surface roughness, high optical reflectance and low sheet resistivity while we could decrease the back contact thickness to 600 nm. That is two thirds to half of the thickness that is currently being used for bilayer and single layer back contact for thin-film solar cells. We demonstrate the excellent properties of Mo/Cr bilayer as back contact of a CZTS solar cell.

13 February 2025 in Smart Materials and Structures
Verified
Journal Article
Closed access
FAFawad Ali
Fawad Ali
IPImran Parvez
Imran Parvez
MAMohammad Albakri
Mohammad Albakri
Polyvinylidene fluoride (PVDF) is a smart piezoelectric material with remarkable properties, offering vast potential for applications in areas such as energy harvesting, biomedical devices, and sensors. Among its various crystalline phases, the β-phase is the most electroactive, characterized by high dielectric properties. Recently, PVDF has been processed using 3D printing due to the technology’s ability to fabricate complex and intricate structures, along with advantages such as design flexibility, material efficiency, and rapid prototyping. While the β-phase content in PVDF is often enhanced through additives or post-processing, limited attention has been given to the role of feedstock preparation and extrusion parameters in phase enhancement. In this study, we investigated how feedstock preparation and extrusion parameters influence the β-phase content of PVDF, aiming to optimize its piezoelectric properties for 3D printing applications. PVDF filaments were produced using two different methods: direct extrusion from PVDF pellets and a solution-based process involving dissolution in a solvent, followed by extrusion. Phase content, structural changes, and thermal stability were assessed using x-ray diffraction (XRD), Fourier-transform infrared spectroscopy, and differential scanning calorimetry. Results show that feedstock processing conditions significantly impact the crystallinity and β-phase concentration in PVDF filaments. Notably, solution-processed PVDF exhibited a higher β-phase concentration compared to the pellet-based method, suggesting that this approach may enhance piezoelectric performance. This study highlights the importance of feedstock processing techniques as a means of tailoring the electroactive properties of PVDF for advanced 3D-printed applications.

14 September 2018 in ChemSusChem
Verified
Journal Article
Open access
PDF file
FAFawad Ali
Fawad Ali
NPNgoc Duy Pham
Ngoc Duy Pham
HBH. Jonathan Bradford
H. Jonathan Bradford
NKNima Khoshsirat
Nima Khoshsirat
KOKen Ostrikov
Ken Ostrikov
TTTuquabo Tesfamichael
Tuquabo Tesfamichael
Invited for this month's cover is group of Tuquabo Tesfamichael at Queensland Univeristy of Technology. The image shows SnOx thin film deposited by sputtering with oxygen vacancies to be used as electron transporting layer in perovskite solar cells. The Full Paper itself is available at 10.1002/cssc.201801541.