8 November 2019 in IEEE Journal of Solid-State Circuits
A fully integrated 76-81-GHz frequency-modulated, continuous-wave (FMCW) radar transceiver (TRX) in a 65-nm CMOS is presented. Two transmitters (TXs) and three receivers (RXs) are integrated for multiple-input multiple-output (MIMO) processing. A 38.5-GHz mixed-mode phase-locked loop (PLL) with reconfigurable loop bandwidth and a frequency doubling scheme are employed to generate the reconfigurable FMCW chirp waveforms. The coarse-to-fine-segmented current DAC is utilized to support sawtooth FMCW chirps with fast frequency ramping-down capability, and the delay lock loop (DLL)-based delay time calibration is used to improve the linearity of the embedded 2-D Vernier time-to-digital converter (TDC). Passive voltage-mode down-conversion is utilized to improve the RX linearity against TX leakage and short-range interference. A bottom-switching Gilbert-type modulator in the TX is proposed to realize the bi-phase modulation, and the magnetically coupled resonator technique is used to effectively expand the link bandwidth. The measurement results show that the FMCW TRX could generate reconfigurable chirps with the bandwidth from 250 MHz to 4 GHz and the period from 30 μs to 10 ms. The root-mean-square (rms) frequency error is 110 kHz for a sawtooth chirp with 4-GHz bandwidth and 300-μs period. The TX maximum output power is 13.4 dBm and is adjustable within 3 dB by reconfiguring its low dropout regulator (LDO) voltage. The RX achieves a 15.3-dB noise figure at 600-kHz IF and a -8.5-dBm RF input-referred P1dB. The overall power consumption is 921 mW, with two TXs and three RXs powered ON. Based on the proposed TRX chip, prototype hardware and a data process algorithm are developed. Real-time experimental results show that the distance and the angular resolution of the MIMO radar achieved are 5 cm and 9$°, respectively.
28 June 2022 in IEEE Journal of Solid-State Circuits
A $D$ -band joint radar-communication complementary metal–oxide–semiconductor (CMOS) transceiver featuring a dual-function mode multiplexer, a power-combining PA with high output power, a current choking high-gain mixer, a two-point modulation (TPM) frequency-modulated continuous-wave (FMCW) digital phase-locked loop (PLL) with a dual-core DCO, and a wideband I/Q local oscillator (LO) generator is implemented in 28-nm CMOS technology. In the radar mode, the RF front end demonstrates 46-GHz bandwidth (BW), and the on-chip PLL/LO generated FMCW chirp achieves a BW of 30 GHz and a slope of 30 GHz/50 $\mu$ s. In the communication mode, the transceiver including the analog baseband realizes 20-GHz BW, and the image rejection ratio (IRR) is better than 40 dB. The measured transmitter (TX) saturated output power is 13 dBm, and the output 1-dB compression point (OP1dB) is 8.3 dBm. The measured typical PLL phase noise is $-$ 111.3 dBc/Hz at a 1-MHz offset from an 11.69-GHz carrier frequency. The TX-to-RX over-the-air (OTA) modulation–demodulation measurement with QPSK and 16-QAM signals shows the error vector magnitude (EVM) of $-$ 16.5 and $-$ 19.7 dB, respectively.
2 December 2021 in IEEE Journal of Solid-State Circuits
Different from the conventional two-point modulation (TPM) type-II phase-locked loops (PLLs) requiring non-trivial gain calibrations and TPM type-III PLLs with loop stability concern and limited chirp rate, a self-adapting gain mismatch TPM type-II digital PLL is proposed in this article. It directly detects frequency error as its input signal, allowing frequency ramp tracking with zero steady-state frequency error using a type-II PLL. In addition, the maximum trackable slope in the case of the proposed TPM type-II PLL is intrinsically larger than that of the conventional TPM type-III PLL. A polarity navigator is embedded in the digital loop filter to improve the linearity at the chirp turning-around points (TAPs). Fabricated in a 28-nm complementary metal–oxide–semiconductor (CMOS) technology, the proposed PLL consumes 23 mW from a 1-V power supply and occupies 0.31 mm 2 . The measurement results indicate that the proposed PLL can generate a precise triangular chirp with 2.27-GHz bandwidth (BW) and 18.2- $\mu \text{s}$ period at 12.5 GHz. To the best knowledge of the authors, this work demonstrates the widest normalized Chirp-bandwidth and the fastest chirp rate simultaneously.
22 October 2019 in IEEE Transactions on Circuits and Systems I: Regular Papers
A 77-GHz frequency-modulated continuous-wave (FMCW) generator is presented for millimeter-wave (mm-wave) radar applications. The FMCW chirp is provided by a mixed-mode phase-locked loop (PLL). A dual rising-edge fractional-phase detector based on time-to-digital converter (TDC) is proposed to overcome the problem caused by the rising and falling time mismatch. A 2.3 ns detection range, 10 ps resolution Vernier TDC is employed in the detector to cover the two consecutive rising edges with less power consumption. A self-calibrated delay chain is employed in the Vernier TDC to overcome process, voltage and temperature (PVT) variations. Furthermore, sampling-edge selection technique is utilized to avoid the glitch during phase detection. A divider-less frequency error estimator is presented to save area and power. By employing a coarse-fine segmented digital-to-analog converter (DAC), the generator supports triangular and sawtooth-like FMCW chirp with reconfigurable period and bandwidth. An LC voltage- controlled oscillator (VCO) with split varactor is proposed to improve the linear tuning range. Implemented in 65 nm CMOS, the FMCW generator consumes 99 mW power and 0.7 mm x 0.8 mm chip area. The measurement results show that the phase noise from 78.7 GHz carrier is -87.4-dBc/Hz at 1 MHz offset. The measured root-mean-square (RMS) frequency error of a sawtooth-like FMCW chirp with 4 GHz bandwidth and 0.1 ms period is 205 kHz.
5 May 2023 in Nanophotonics
Passive daytime radiative cooling (PDRC) as a zero‐energy cooling technology that reflects most of sunlight and emits infrared thermal radiation to outer space, has attracted much attention. However, most PDRC materials suffer dust accumulation problem during long‐term use, seriously detrimental to their cooling performance. Here, we demonstrate a micro‐structured polyethylene film fabricated through a scalable hot embossing lithography (named HELPE), enables good superhydrophobic property and therefore excellent self‐cleaning performance as a universal protective layer for most PDRC materials. Specifically, the precisely designed three‐dimensional periodic micron columns on polyethylene film allow for high water droplet contact angle of 151°, and the intrinsic molecular bindings of polyethylene endow low solar absorption ( A = 3.3 %) and high mid‐infrared transmission ( T = 82.3 %) for negligible optical impacts on underlying PDRC materials. Taking polyvinylidene fluoride (PVDF) radiative cooler as an example, when covered with the HELPE film the net cooling performance maintains unchanged (7.5 °C in daytime and 4.5 °C in nighttime) compared to that without HELPE film. After 12 days continuous outdoor experiment, none of obvious dust accumulation can be observed on the radiative cooler covered with HELPE film. Our work offers a universal pathway for most PDRC materials toward practical applications with minimal maintenance need.