3 July 2019 in IEEE Transactions on Control Systems Technology
Incorporating traffic information in power management optimization process for electrified and connected vehicles offers opportunities for improving fuel economy. Integrating the management of thermal load (such as those used for heating, ventilation, & air conditioning (HVAC) of the passenger compartment, and for the battery cooling) with the power management process can provide even greater benefits for connected and automated vehicles (CAVs). However, given the relatively slow dynamics associated with the thermal subsystems, the lack of reliable power and thermal loads prediction over an extended prediction horizon is the main challenge for efficient thermal management using model predictive control (MPC). This paper presents a hierarchical two-layer MPC scheme which exploits vehicle speed and traffic preview predictions over short and long prediction horizons to schedule optimal thermal trajectories for the cabin and battery cooling in hybrid electric vehicles (HEVs) via a novel intelligent online constraint handling (IOCH) approach. These trajectories are next incorporated into the vehicle-level controller to determine the proper power split between electric motor and internal combustion engine (ICE). We present the development and experimental validation of control-oriented models used for prediction of the vehicle thermal dynamics and loads over a long planning horizon. Compared to a more traditional single-layer MPC approach, the proposed two-layer MPC shows that depending on the driving cycle and traffic conditions, 2.2% to 5.3% reductions in HEV fuel consumption can be achieved for urban driving and congested city driving cycles, respectively, in CAV operation scenario. This fuel economy improvement is a direct result of taking proactive actions through real-time prediction and optimization to avoid conservative and inefficient thermal responses, while enforcing cabin and battery operating constraints.
9 March 2020 in IEEE Transactions on Control Systems Technology
Connected and autonomous vehicles (CAVs) have situational awareness that can be exploited for optimal power and thermal management. In this article, we develop a hierarchical model predictive control (H-MPC) strategy for eco-cooling of CAVs, which reduces energy consumption through real-time prediction and multi-timescale and multi-layer optimization. The application of the proposed H-MPC is studied for battery thermal and energy management of an electric vehicle (EV). Our H-MPC approach addresses the uncertainty in the long-term preview of the vehicle speed through robust constraint handling to prevent constraint violation. The simulation results show that compared with a conventional battery thermal management (BTM) strategy, the proposed robust H-MPC saves the battery energy by up to 5.4% under the uncertainties in the long-term vehicle speed predictions in an urban CAV operation scenario.
6 June 2018 in IEEE Transactions on Vehicular Technology
Connected and automated hybrid electric vehicles (CAHEVs) are a potential solution to the future transportation due to their improved fuel economy, reduced emissions, and capability to mitigate congestion and improve safety. The battery thermal management (BTM) in CAHEVs is one of the crucial problems, because the lithium-ion batteries are highly temperature-sensitive and the critical high or low temperatures have a significant impact on the performance and life cycle of lithium-ion batteries. Therefore, a practical and energy-efficient BTM strategy is required for both improving the operating temperature of batteries and saving energy. In this study, the dynamic programming (DP) is implemented for a BTM system in CAHEVs for achieving the optimal cooling/heating energy savings for batteries. To alleviate the computational complexity and reduce the data storage requirement, an iterative approach is proposed to approximate the optimum control strategy iteratively in a multidimensional search space. With an enhanced real-time capability, the proposed iterative DP strategy can improve the system performance and energy-efficiency by fully exploiting the future road information in CAHEVs combined with a model predictive control method. The hardware-in-the-loop (HIL) validation of the proposed strategy is conducted on the UDDS and the WLTC drive cycles based on a Toyota Prius PHEV model. The results demonstrate the feasibility and effectiveness of the proposed BTM strategy that leads to a considerable BTM energy reduction.
22 October 2018 in IEEE Transactions on Power Electronics
Online State of Charge (SoC) and State of Health (SoH) estimation is essential for efficient, safe, and reliable operation of Lithium ion batteries. Based on the first-order equivalent circuit model (ECM), a multi-scale extended Kalman filter is adopted in this paper to estimate ECM parameters and battery SoC using dual time scales. The nature of the battery excitations significantly influences the estimation performance. When the input-output data, i.e., the input current and output voltage, is insufficiently rich in frequency content, the estimation performance is poor. Thus the excitation current should be optimized for accurate estimation of parameters and states. A Cramer-Rao bound analysis is conducted, considering voltage noise, current amplitude, and current frequency, which shows the loss of accuracy in multi-parameter estimation (estimating all states and parameters) when compared to single-parameter estimation (estimating only one parameter/state). However, it also shows that the loss of accuracy can be significantly reduced when the excitation current is carefully chosen to satisfy certain criteria. Both simulation and experimental results verify the analysis results and show that a current profile with optimal frequency components achieves the best estimation performance, thereby providing guidelines for designing battery current profiles for improved SoC and SoH estimation performance.
8 July 2021 in IEEE Transactions on Control Systems Technology
In this article, we propose a multihorizon model predictive control (MH-MPC) approach with applications to integrated power and thermal management (iPTM) of connected hybrid electric vehicles (HEVs). The proposed MH-MPC leverages preview and optimization over a short receding and a long shrinking horizon, where the accuracy of preview, model, and integration can be different over different horizons. Compared with a conventional MPC-based approach with a short prediction horizon and terminal cost, the MH-MPC improves fuel consumption to a level comparable to dynamic programming (DP) while still being computationally affordable. A statistical sensitivity analysis over real-world city driving cycles is conducted to demonstrate the robustness of MH-MPC to moderate levels of uncertainty in the long-term preview.
12 October 2023 in IEEE Transactions on Transportation Electrification
Predicting the remaining useful life (RUL) of a lithium-ion battery with its limited degradation history is critical as it ensures timely maintenance of electric vehicles and efficient reuse of second-life batteries. Considering realistic battery operating conditions, this work investigates the RUL prediction under partial charge and discharge with a limited degradation history of the target cell. Given its ability to inform feature importance, the random forest is adopted to help prioritize different battery measurements and identify the least amount of operating data required for accurate RUL prediction. By examining the prediction performance using one complete charge and discharge cycle, it is shown that the duration, used capacity, and voltage signals of both charge and discharge contain important features related to battery RUL. The prediction performance under partial charge and discharge is also studied under state-of-charge (SOC) uncertainties, revealing satisfactory performance achieved with the data collected over the SOC range of [0.2, 0.8]. Comparison with an existing convolutional neural network-based approach that uses four complete charge and discharge cycles verifies the enhanced onboard feasibility of the proposed approach. Sensitivity analysis against SOC ranges shows that the data in the SOC range of [0.1, 0.2] contain the richest RUL-related information for lithium iron phosphate cells. Extensive validation on cells with different chemistry, ambient temperatures, and C rates further demonstrates the robustness of the proposed approach.