13 February 2024 in IEEE Transactions on Power Electronics
The interfacial electrical tree (IET) between the packaging insulation and the ceramic substrate is easily initiated by a high electric field around the triple point in the power modules, and the IET resistance is not considered in the current packaging insulation design. This article proposes a low-content POSS-grafted silicone elastomer nanocomposite to hinder the IET growth, and its electrical, thermal, and mechanical properties are tested. The IET patterns and the accompanying partial discharge (PD) characteristics are also investigated in the lateral and vertical packaging modules at low and high temperatures. The IET in the packaging modules appears at a much lower voltage than their breakdown voltage and takes longer until the ultimate breakdown of the modules. Besides, the IET is initiated at a lower voltage and grows faster at higher temperatures. The grafted nanocomposite packaging insulation inhibits the IET growth and decreases the IET breakdown probability by its reduced charge carrier mobility and enhanced molecular interaction. The mechanisms of inhibited charge transport on the enhanced electrical properties and hindered IET growth are revealed. Combined with the quantum chemical calculations, bipolar charge transport, and IET phase-field simulations, the design criteria and procedure for high-temperature IET-resistant packaging insulation are proposed.
30 May 2022 in IEEE Transactions on Components, Packaging and Manufacturing Technology
This article explores the potential of epoxy resin/silicon carbide whisker (EP/SiCw) composites (1 wt%, 2 wt%, 3 wt%, 4 wt%, 5 wt%) as the field-dependent conductivity (FDC) packaging materials for the high-voltage power modules by investigating their thermal and electrical properties at different temperatures. The cross-sectional morphology of the prepared materials is characterized by field emission-scanning electron microscopy (FE-SEM). The thermal analysis consists of differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA). The electrical properties, such as dc conductivity, dielectric spectroscopy, thermally stimulated discharge current (TSDC), space charge distribution, and dc breakdown strength, are measured. The molecular orbital energy levels of the EP and SiCw monomers are calculated by quantum chemical calculation (QCC) to analyze the effect of EP interfacial trap sites on the electrical properties. The effect of the EP/SiCw interfacial charges and electrical field distortion on the electrical properties of the EP/SiCw composites with different filler content is investigated by the finite-element method (FEM) simulation. It is found that the 2 wt% EP/SiCw composite has a better thermal performance. The 1 wt% has lower real permittivity, lower trap density, lower space charge accumulation, and higher breakdown strength. The EP/SiCw composites have a higher trap level than the pure EP. The nonlinearity percolation threshold of the EP/SiCw composites is 3 wt%. As the filler content increases, the nonlinear conductivity coefficient of the EP/SiCw composites becomes higher, whereas the breakdown strength decreases due to the electric field distortion near the electrodes caused by the apparent hetero charge accumulation at high filler content.
7 January 2022 in Nanotechnology
This research investigates the optimal region to achieve balanced thermal and electrical insulation properties of epoxy (EP) under high frequency (HF) and high temperature (HT) via integration of surface-modified hexagonal boron nitride (h-BN) nanoparticles. The effects of nanoparticle content and high temperature on various electrical (DC, AC, and high frequency) and thermal properties of EP are investigated. It is found that the nano h-BN addition enhances thermal performance and weakens electrical insulation properties. On the other side, under HF and HT stress, the presence of h-BN nanoparticles significantly improves the electrical performance of BN/EP nanocomposites. The EP has superior insulation properties at low temperature and low frequency, whereas the BN/EP nanocomposites exhibit better insulation performance than EP under HF and HT. The factors such as homogeneous nanoparticle dispersion in EP, enhanced thermal conductivity, nanoparticle surface modification, weight percent of nanoparticles, the mismatch between the relative permittivity of EP and nano h-BN, and the presence of voids in nanocomposites play the crucial role. The optimal nanoparticle content and homogenous dispersion can produce suitable EP composites for the high frequency and high temperature environment, particularly solid-state transformer applications.
5 September 2022 in Nanotechnology
This paper reports an enhancement of the nonlinear conductivity, thermal and mechanical properties of micro-silicon carbide/silicone elastomer (m-SiC/SE) composites by adding nano-aluminum nitride (n-AlN) for power module encapsulation applications. The electrical properties (such as nonlinear conductivity characteristics and transient permittivity obtained from polarization current, and trap distributions obtained from thermally stimulated depolarization current) and material properties (including thermo-gravimetric analysis, coefficient of thermal expansion (CTE), and thermal conductivity, tensile strength, strain at break and Young’s modulus) of the pure SE, m-SiC/SE microcomposites, m-SiC/n-AlN/SE hybrid composites are investigated. The effect of the m-SiC fillers and n-AlN fillers on physicochemical properties of the SE matrix is analyzed by FT-IR spectroscopy and crosslinking degree. The measured nonlinear conductivity and transient permittivity are used for electric field simulation under DC stationary and square voltages. It is found that the addition of n-AlN fillers in the SE hybrid composite improves the nonlinear conductivity characteristics and mitigates the electric field under DC stationary and square voltages, compared to the SE microcomposite. Furthermore, the m-SiC/n-AlN/SE hybrid composite has a higher thermal degradation temperature, thermal conductivity, tensile strength, Young’s modulus, and crosslinking degree than the SE microcomposite, whereas their CTE and strain at break are lower. It is elucidated that the m-SiC/n-AlN/SE hybrid composite with enhanced nonlinear conductivity and material properties is a promising packaging material for high-voltage power modules.
5 January 2022 in ACS Applied Electronic Materials
7 December 2021 in IEEE Transactions on Components, Packaging and Manufacturing Technology
This work focuses on the performance of epoxy microcomposites, nanocomposites, and micro–nano hybrid composites as the packaging material of the power modules. The experiments consist of thermal conductivity, differential scanning calorimetry (DSC), space charge, dc electrical conductivity, thermally stimulated depolarization current (TSDC), and dielectric spectroscopy measurements. Moreover, the ac stationary electric field simulation and the dc transient electric field simulation are performed to analyze the electrical performance of the epoxy composites as the packaging materials in the power module structure under ac voltage and dc voltage, respectively. The ac field simulation uses dielectric spectroscopy data to obtain the electric field and power loss of the epoxy composites at different temperatures and frequencies under the ac voltage. On the other side, the dc electrical conductivity and TSDC experiment data are used for the dc transient electric field simulation to obtain the electric field considering the space charge under the dc voltage. The results show that the optimal addition of the filler content (20 wt% micro-AlN and 5 wt% nano-AlN) in the epoxy micro–nano hybrid composites can reduce the power loss and electric field at 150 °C and 1 MHz, under the ac condition. Furthermore, considering the space charge under the dc voltage, the electric field can also be reduced in epoxy micro–nano hybrid composites compared to pure epoxy.