30 April 2022 in Eastern-European Journal of Enterprise Technologies
Energy consumption, environmental issues, product quality are actual problems related to grain drying processes. It is necessary to pay attention to designing new structures of energy-efficient grain dryers. A structure of an energy-efficient grain dryer based on thermosiphons has been designed; its energy consumption is 3.5...6.8 MJ/kg depending on surface temperature and air flow rate. The dryer includes a layer heater, a drying chamber, a heat generator, a heater, a noria for loading the product, and fans. The structural features of the dryer allow the drying process to be carried out without direct contact between the combustion gases and the product. The efficiency of the designed structure was evaluated for such indicators as heat transfer coefficients to the grain flow, specific energy costs, moisture content, the relative humidity of the air leaving the dryer. The values of coefficients of the heat transfer to the grain flow vary within 36...58 W/m2K at speeds 2.5...8 mm/s. An increase in the flow rate by 3.2 times leads to an increase in the heat transfer coefficient by 1.6 times. The moisture content of the air at the outlet of the dryer reaches 60 g/kg, while the relative humidity is 90 %, which is several times higher than the parameters for convective mine grain dryers. Energy consumption for drying at the surface temperature of thermosiphons Ts=142.9 °C for various grain flow rates is close to a minimum. The energy consumption is lower than in existing convective dryers. 21 % is spent on heating grain in the dryer; 54 % ‒ on moisture evaporation; and 23.6 % are losses. If we consider the energy spent on moisture evaporation usable, the efficiency of convective dryers is only 40 % while that of dryers based on thermosiphons is 54.1 %. It is expected that the designed structure could be a solution for small farmers in the post-harvest drying process
30 April 2021 in Eastern-European Journal of Enterprise Technologies
The designs of cryoconcentrators of block type BV-2 and BL-20 have been developed. The influence of design and operating parameters on the kinetics of freezing of pomegranate juice was investigated. A decrease in the operating temperature of the refrigeration unit contributes to a more intensive growth of the ice block. When the temperature of the coolant decreases by 1.2 times, the productivity of the BV-2 unit increases by 27 %, and of the BL-20 unit by 12 %. For BL-20, an increase in the initial concentration by 3 times leads to a decrease in productivity by 2.5...1.5 times. The influence of the temperature of the coolant and the initial concentration of the juice on the rate of concentration change has been determined. At low initial concentrations of solutions (10...15 %), a sharp increase in concentration is observed at the final stage of freezing. The dry matter content of the juice is increased by 16 % at high concentrations, only 4 %. The kinetics of the ice block separation process has been studied. At the first stage (duration 10...15 minutes), the concentration of effluents is 2...3 % higher than the concentration of the solution. On the second, increases by 6...10 %. In the third stage, there is a monotonous decrease in effluent concentration (2.5 % / hour). The results of experimental modeling are generalized. The obtained equation in similarity numbers allows calculating the mass transfer coefficients with an error of no more than 20 %. The developed designs of the BL-20 and BV-2 cryoconcentrators are semi-industrial units. With block cryoconcentration, a concentration of pomegranate juice of 47° Brix was achieved, which is higher than in traditional devices. The results obtained can be applied for further development and creation of industrial plants with optimal improved product parameters.
15 January 2022 in Research in Agricultural Engineering
Theoretical justification of the operating modes of periodic activity of vegetable oil purification | Petr Igorevich Osadchuk, Dmitry Panasovich Domuschi, Yuriy Ivanovich Enakiev, Blagoj Elenov | Agricultural Journals
18 June 2026 in Technology audit and production reserves
The object of research is the process of mechanical oil extraction from sunflower seeds in a single-screw press and the influence of the geometric parameters of the screw shaft on its performance efficiency. The paper addresses the problem of improving pressing efficiency by identifying reserves for process intensification through optimization of the screw shaft design. The influence of the flight pitch, segment length, and inner diameter on the formation of the compression ratio of the raw material and the pressure distribution along the working zone of the press is analyzed. Experimental researches were carried out using a screw press with a capacity of up to 200 kg/h, allowing variation of the geometric parameters of the screw segments. Configurations of the screw shaft with a flight pitch in the range of 40–140 mm, segment length of 40–200 mm, and inner diameter of 82–132 mm were investigated. It was established that these parameters determine the compression ratio of the material within the range of 13.6–14.6 and affect the pressure distribution and the pattern of oil flow along the pressing chamber. It is shown that reducing the flight pitch to 40–56 mm and increasing the inner diameter to 128–132 mm leads to a shift of the maximum pressure zone toward the outlet section of the press. It was experimentally confirmed that the rational compression ratio is 13.6, at which the maximum oil yield reaches 37% under single-stage cold pressing conditions. It was found that a further increase in the compression ratio to 14.6 does not lead to an increase in oil yield but results in higher crushed oil cake formation and a decrease in overall process efficiency. It was determined that optimization of the geometry of the first screw flights, in particular the rational combination of the parameters of the first segment (Ø82/140 mm, L = 192 mm, S = 120 mm) and the second segment (Ø82/140 mm, L = 90 mm, S = 80 mm) makes it possible to increase the press productivity without increasing raw material losses. The obtained results can be used to improve the design of screw presses for small-scale production and to enhance their technical and economic performance.