Saroj Kumar Patra

Saroj Kumar Patra

Auto-generated profile, based on publicly available information

Saroj Kumar Patra

Department of Physics, Norwegian University of Science and Technology (NTNU), NO-7491 Trondheim, Norway

Research Focus & Metrics

Academic Career Length

18Years (2009-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 February 2009 in Physica E: Low-dimensional Systems and Nanostructures
Verified
Journal Article
Closed access
PSP.K. Samanta
P.K. Samanta
SPS.K. Patra
S.K. Patra
PCP. Roy Chaudhuri
P. Roy Chaudhuri

1 December 2011 in Journal of Crystal Growth
Verified
Journal Article
Closed access
TNTron Arne Nilsen
Tron Arne Nilsen
SPSaroj Kumar Patra
Saroj Kumar Patra
MBMagnus Breivik
Magnus Breivik
BFBjørn-Ove Fimland
Bjørn-Ove Fimland

1 April 2017 in Journal of Crystal Growth
Verified
Journal Article
Closed access
SPSaroj Kumar Patra
Saroj Kumar Patra
TTThanh-Nam Tran
Thanh-Nam Tran
LVLasse Vines
Lasse Vines
IKIlia Kolevatov
Ilia Kolevatov
EMEdouard Monakhov
Edouard Monakhov
BFBjørn-Ove Fimland
Bjørn-Ove Fimland

1 November 2015 in Journal of Vacuum Science & Technology B
Verified
Journal Article
Closed access
PDF file
TTThanh-Nam Tran
Thanh-Nam Tran
SPSaroj Kumar Patra
Saroj Kumar Patra
MBMagnus Breivik
Magnus Breivik
BFBjørn-Ove Fimland
Bjørn-Ove Fimland
The effect of several plasma-assisted oxide removal techniques prior to metallization of p-type GaSb was investigated. Compared to conventional chemical methods, the plasma-assisted oxide removal resulted in significant improvement of the specific contact resistivities, obtained from transfer length method measurements. Very low specific contact resistivities of less than 5 × 10−8 Ω cm2 were observed after surface pretreatment by H2/Ar sputter etching and low-ion-energy argon irradiation. By eliminating sample exposure to air, in situ Ar irradiation becomes a promising technique for high performance GaSb-based semiconductor diode lasers.

14 October 2025 in Journal of Physics: Energy
Verified
Journal Article
Open access
EPEmil Mihai Pavelescu
Emil Mihai Pavelescu
SPSaroj Kumar Patra
Saroj Kumar Patra
Cosmin RomanitanCosmin Romanitan
Cosmin Romanitan
AMAlina Matei
Alina Matei
ØDØystein Dahl
Øystein Dahl
BFBjørn-Ove Fimland
Bjørn-Ove Fimland
Intermediate band solar cells (IBSCs) have the potential to overcome the efficiency limit of single-bandgap solar cells. Dilute nitride III–V alloys, with splitting of the conduction band due to band anticrossing, can be used as the intermediate-band material for solar cell applications. In this work, we report on the introduction of engineered GaInNAs alloy, with low (dilute) In and N contents, as IBSC material and the comparison of the performances of GaInNAs-based and the corresponding In-free GaNAs-based IBSCs grown on GaAs (100) substrate. Introduction of a small amount of In (3%) in a GaN0.011As0.989-based IBSC was found to noticeably increase the short-circuit current, I sc, at the expense of a small decrease in the open-circuit voltage, V oc. When annealed at 750 °C for 90 s, significant enhancements in I sc and V oc are seen, especially in the In-containing solar cell. The observed In-related enhancement in cell parameters after annealing is related to In-promoted bandgap tailoring and efficient curing of carrier traps during annealing. This occurred without change in the macroscopic composition of the GaInNAs alloy, most likely by In-N bond formation upon annealing, a phenomenon which does not exist in the GaNAs alloy.

21 July 2025 in IEEE Photonics Technology Letters
Verified
Journal Article
Closed access
TTThanh-Nam Tran
Thanh-Nam Tran
SPSaroj Kumar Patra
Saroj Kumar Patra
MBMagnus Breivik
Magnus Breivik
BFBjørn-Ove Fimland
Bjørn-Ove Fimland
A novel tunable coupled lasers structure utilizing the Vernier effect and the light coupling mechanism is successfully demonstrated in the wavelength range of 2.35 – $2.39~\mu $ m. The coupling effect between two active S-bend and straight waveguide lasers can enable both a wide tuning range and a very high side mode suppression ratio (SMSR) by choosing an appropriate separation gap between these two lasers. With a separation gap of $5~\mu $ m, a wide tuning range of 40 nm and a stable SMSR of above 40 dB was achieved. Employing a simple structure, this regrowth-free and easily manufactured laser configuration is a highly promising solution for trace-gas sensing applications.