The development of electrodes for ambient temperature sodium-ion batteries requires the study of new materials and the understanding of how crystal structure influences properties. In this study, we investigate where sodium locates in two Prussian blue analogues, Fe[Fe(CN)6]1−x·yH2O and FeCo(CN)6. The evolution of the sodium site occupancies, lattice and volume is shown during charge–discharge using in situ synchrotron X-ray powder diffraction data. Sodium insertion is found to occur in these electrodes during cell construction and therefore Fe[Fe(CN)6]1−x·yH2O and FeCo(CN)6 can be used as positive electrodes. NazFeFe(CN)6 electrodes feature higher reversible capacities relative to NazFeCo(CN)6 electrodes which can be associated with a combination of structural factors, for example, a major sodium-containing phase, ∼Na0.5FeFe(CN)6 with sodium locating either at the x = y = z = 0.25 or x = y = 0.25 and z = 0.227(11) sites and an electrochemically inactive sodium-free Fe[Fe(CN)6]1−x·yH2O phase. This study demonstrates that key questions about electrode performance and attributes in sodium-ion batteries can be addressed using time-resolved in situ synchrotron X-ray diffraction studies.
Titanium doping in lithium manganese oxide spinels was shown to be beneficial for the structural stability of the potential Li-ion battery cathode materialsLiTixMn2−xO4 (0.2 ≤ x ≤ 1.5), yet the distribution of Li/Ti/Mn in the structure and the cation oxidation states, both pivotal for the electrochemical performance of the material, is not fully understood. Our work investigates the changes in the local ordering of the ions throughout this series, by using a combination of 7Li NMR spectroscopy and ab initio DFT calculations. The7Li NMR shifts are first calculated for a variety of Li configurations with different numbers and arrangements of Mn ions in the first metal coordination shell, and then decomposed into Li-O-Mn bond pathway contributions to the shift. These Li-O-Mn bond pathways are then used to simulate and assign the experimental NMR spectra of different configurations and stoichiometries beyond those in the initial subset of configurations via a random distribution model and a Reverse Monte-Carlo approach. This methodology enables a detailed understanding of the experimental 7Li NMR spectra, allowing the variations in the local ordering of the ions in the structure to be identified. A random distribution of Ti4+-Mn3+/4+ sites is found at low Ti-content (x=0.2), an inhomogeneous lattice of Mn4+-rich and Ti4+-rich domains is identified for x=0.4 and single-phase solid solution is observed for x=0.6 and x=0.8. A mixed Li-Mn2+ tetrahedral and Li-Mn3+/4+-Ti octahedral configuration is determined for the x=1.0 case. A specific cation ordering in the partially inverse LiTi1.5Mn0.5O4 case is found, which transforms into a two-phase network of disordered Mn3+-rich and ordered Mn2+-rich domains for x=1.1 - 1.4.
22 August 2018 in Acta Crystallographica Section A Foundations and Advances
For high-resolution powder diffraction in material science, high photon energies are necessary, especially for in situ and in operando experiments. For this purpose, a multi-analyser detector (MAD) was developed for the high-energy beamline P02.1 at PETRA III of the Deutsches Elektronen-Synchrotron (DESY). In order to be able to adjust the detector for the high photon energies of 60 keV, an individually adjustable analyser–crystal setup was designed. The adjustment is performed via piezo stepper motors for each of the ten channels. The detector shows a low and flat background as well as a high signal-to-noise ratio. A range of standard materials were measured for characterizing the performance. Two exemplary experiments were performed to demonstrate the potential for sophisticated structural analysis with the MAD: (i) the structure of a complex material based on strontium niobate titanate and strontium niobate zirconate was determined and (ii) an in situ stroboscopy experiment with an applied electric field on a highly absorbing piezoceramic was performed. These experiments demonstrate the capabilities of the new MAD, which advances the frontiers of the structural characterization of materials.