The improvement of rechargeable zinc/air batteries was a hot topic in recent years. Predominantly, the influence of water and additives on the structure of the Zn deposit and the possible dendrite formation were studied. However, the effect of the surface structure of the underlying substrate was not focused on in detail, yet. We now show the differences in electrochemical deposition of Zn onto Au(111) and Au(100) from the ionic liquid N‐methyl‐N‐propylpiperidinium bis(trifluoromethanesulfonyl)imide. The fundamental processes were initially characterized via cyclic voltammetry and in situ scanning tunnelling microscopy. Bulk deposits were then examined using Auger electron spectroscopy and scanning electron microscopy. Different structures of Zn deposits are observed during the initial stages of electrocrystallisation on both electrodes, which reveals the strong influence of the crystallographic orientation on the metal deposition of zinc on gold.
The growth of noble‐metal single crystals via the flame fusion method was developed in the 1980s. Since then, there have been no major advancements to the technique until the recent development of the controlled‐atmosphere flame fusion (CAFF) method to grow non‐noble Ni single crystals. Herein, we demonstrate the generality of this method with the first preparation of fcc Cu as well as the first hcp and bcc single crystals of Co and Fe, respectively. The high quality of the single crystals was verified using scanning electron microscopy and Laue X‐ray backscattering. Based on Wulff constructions, the equilibrium shapes of the single‐crystal particles were studied, confirming the symmetry of the fcc, hcp, and bcc single‐crystal lattices. The low cost of the CAFF method makes all kinds of high‐quality non‐noble single crystals independent of their lattice accessible for use in electrocatalysis, electrochemistry, surface science, and materials science.
23 August 2021 in Angewandte Chemie International Edition
While numerous reference electrodes suitable for aqueous electrolytes exist, there is no well‐defined standard for non‐aqueous electrolytes. Furthermore, reference electrodes are often large and do not meet the size requirements for small cells. In this work, we present a simple method for fabricating stable 3D‐printed micro‐reference electrodes. The prints are made from polyvinylidene fluoride, which is chemically inert in strong acids, bases, and commonly used non‐aqueous solvents. We chose six different reference systems based on Ag, Cu, Zn, and Na, including three aqueous and three non‐aqueous systems to demonstrate the versatility of the approach. Subsequently, we conducted cyclic voltammetry experiments and measured the potential difference between the aqueous homemade reference electrodes and a commercial Ag/AgCl‐electrode. For the non‐aqueous reference electrodes, we chose the ferrocene redox couple as an internal standard. From these measurements, we deduced that this new class of micro‐reference electrodes is leak‐tight and shows a stable electrode potential.
Sodium‐ion batteries are promising candidates for post‐lithium‐ion batteries. While sodium has a less negative standard electrode potential compared to lithium, it is still a strong reducing agent. Ionic liquids are suitable solvents for sodium metal batteries, since metallic sodium is very reactive, particularly with water and molecules containing acidic hydrogen atoms. In this study, the initial stages of electrodeposition of sodium on Au(111) from N‐methyl‐N‐propylpiperidinium [MPPip] bis(trifluoromethanesulfonyl)imide [TFSI] were studied using voltammetry and in‐situ scanning tunnelling microscopy. Four subsequent underpotential deposition stages were observed: (i) nucleation at the Au(111) reconstruction elbows, followed by (ii) growth of small monoatomically high islands that form (iii) a smooth layer via coalescence, and (iv) further island growth on top of the existing layers. The electrocrystallisation mode changed from smooth layer formation to 3D growth, resulting in cauliflower‐like structures. The deposition process was accompanied by simultaneous alloy formation.
Studying the potential dependent interaction of non-aqueous electrolytes, such as ionic liquids (ILs), with model electrode surfaces plays a crucial role not only in the field of battery-related research. These electrolytes bear the advantage that their electrochemical stability windows often exceed that of water. However, comparing results using ILs as electrolytes reported in the literature reveals strong discrepancies in the reproducibility of the data. In this study, we show that parameters such as the supplier, the supplied batch, and the purification steps can have a huge impact on the electrochemical properties. As a reference system, these properties are studied by cyclic voltammetry on a Au(111) single crystal electrode in N -methyl- N -propylpiperidinium bis(trifluoromethane)sulfonimide ([MPPip][TFSI]). Analysing the different features observed in the cyclic voltammograms, we were to some extent able to deconvolute the features that are related to the interaction of ILs with the substrate and impurities added from the pretreatment due to the influence of residual water and oxygen. Graphical Abstract