The electrodeposition of copper onto Au(111) from Deep Eutectic Solvents (DESs) type III has been studied by cyclic voltammetry. Investigations were carried out with mixtures of choline chloride (ChCl) and ethylene glycol (EG) or trifluoroacetamide (TFA). The eutectic compositions and temperatures were determined by differential scanning calorimetry (DSC). For the ChCl/EG DES, a eutectic ratio of 16 : 84 (ChCl:EG) was found instead of the previously reported ratio of 33 : 67. The electrodeposition of copper was studied for electrolytes with different ratios of ChCl to hydrogen bond donor (HBD) to resolve the influence of the composition on the deposition behavior. Both CuCl and CuCl2 were used as Cu salts. Underpotential deposition (UPD) is followed by bulk deposition with the diffusion rate of Cu species being dependent on the ratio of ChCl to HBD. With CuCl2, both Cu+ and Cu2+ species are reduced and deposited, whereby the two‐electron reduction is more dominant with higher chloride content and presence of EG. However, the properties of the Cu electrodeposition do not result from the freezing‐point depression of the DESs, but from the high concentration of ions.
23 August 2021 in Angewandte Chemie International Edition
While numerous reference electrodes suitable for aqueous electrolytes exist, there is no well‐defined standard for non‐aqueous electrolytes. Furthermore, reference electrodes are often large and do not meet the size requirements for small cells. In this work, we present a simple method for fabricating stable 3D‐printed micro‐reference electrodes. The prints are made from polyvinylidene fluoride, which is chemically inert in strong acids, bases, and commonly used non‐aqueous solvents. We chose six different reference systems based on Ag, Cu, Zn, and Na, including three aqueous and three non‐aqueous systems to demonstrate the versatility of the approach. Subsequently, we conducted cyclic voltammetry experiments and measured the potential difference between the aqueous homemade reference electrodes and a commercial Ag/AgCl‐electrode. For the non‐aqueous reference electrodes, we chose the ferrocene redox couple as an internal standard. From these measurements, we deduced that this new class of micro‐reference electrodes is leak‐tight and shows a stable electrode potential.
The electrochemical behavior of Au(111) in contact with deep eutectic solvents (DESs) was studied by cyclic voltammetry, electrochemical impedance spectroscopy (EIS), and immersion experiments to determine the potential of zero total charge (pztc). In particular, DESs type III consisting of a choline salt and a hydrogen bond donor (HBD) were investigated. The HBDs urea and ethylene glycol (EG) were chosen since they belong, in combination with choline chloride (ChCl), to the most widely studied systems. A third HBD used in this study was trifluoroacetamide (TFAcA) because of its remarkable freezing point depression. The adsorption of chloride, nitrate, and sulfate anions on Au(111) was investigated using DESs, as the electrochemical behavior of Au(111) in aqueous electrolytes containing these anions were already well studied. For a better understanding of the interactions of ions in DESs with noble metal electrode surfaces, Au(111) in aqueous ChCl was investigated as well. It was shown that anion adsorption on Au(111) in the DESs under consideration was similar to adsorption in the respective dilute aqueous systems.
While numerous reference electrodes suitable for aqueous electrolytes exist, there is no well‐defined standard for non‐aqueous electrolytes. Furthermore, reference electrodes are often large and do not meet the size requirements for small cells. In this work, we present a simple method for fabricating stable 3D‐printed micro‐reference electrodes. The prints are made from polyvinylidene fluoride, which is chemically inert in strong acids, bases, and commonly used non‐aqueous solvents. We chose six different reference systems based on Ag, Cu, Zn, and Na, including three aqueous and three non‐aqueous systems to demonstrate the versatility of the approach. Subsequently, we conducted cyclic voltammetry experiments and measured the potential difference between the aqueous homemade reference electrodes and a commercial Ag/AgCl‐electrode. For the non‐aqueous reference electrodes, we chose the ferrocene redox couple as an internal standard. From these measurements, we deduced that this new class of micro‐reference electrodes is leak‐tight and shows a stable electrode potential.