Myeongin Kim

Myeongin Kim

Auto-generated profile, based on publicly available information

Myeongin Kim

Electronic Convergence Materials & Device Research Center, Korea Electronics Technology Institute, Gyeonggi-do, 13509, Korea

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
30 August 2021 in Journal of Welding and Joining
Verified
Journal Article
Open access
PDF file
MKMi Song Song Song Kim
Mi Song Song Song Kim
WHWON SIK HONG
WON SIK HONG
MKMyeongin Kim
Myeongin Kim
In this study, thermo-compression(TC) and vacuum reflow(VR) bonding processes of fine pitch interconnection were optimized using Type 7 Sn-3.0Ag-0.5Cu solder paste. A chip with Cu pillar Sn-2.5Ag bumps and BT substrate with ENEPIG surface finish were used, and the thickness and the aperture ratio of the metal mask were 30 ㎛/50 ㎛ and 70%/100%, respectively. As a result of optimizing the printing process, a metal mask with a thickness of 30 ㎛ and an aperture ratio of 100% was selected. As a result of the TC and VR bonding processes optimization, Cu6Sn5 and (Cu,Ni)6Sn5 IMC layers were formed on the top and bottom of the solder joint, respectively. In the conventional TC process sample, the thickness of the solder was measured to be 4.1 ㎛, and the IMC thickness ratio was calculated to be 40%. Also, in the TC and VR process samples with solder paste, the thickness of the solder was measured to be 6.5 ㎛ and 10.3 ㎛, respectively, and the ratio of the IMC thickness was calculated to be about 32% and 43%. It was expected that it would be beneficial to reliability by reducing the occurrence and propagation of cracks in the solder joint due to the effect of lowering the IMC thickness ratio as the volume of the solder becomes larger than that of the conventional TC process.

30 August 2021 in Journal of Welding and Joining
Verified
Journal Article
Open access
PDF file
WHWON SIK HONG
WON SIK HONG
MKMi Song Song Song Kim
Mi Song Song Song Kim
MKMyeongin Kim
Myeongin Kim
After the joining of small 1005 and 0603 multilayer ceramic capacitor (MLCC) components for a semiconductor package using Type 4 (T4) and Type 7 (T7) Sn-3.0Ag-0.5Cu (SAC305), T4 Sn-1.0Ag-0.5Cu (SAC105), and T4 Sn-0.3Ag-0.7Cu (SAC0307) solder pastes, the differences between hot air reflow and vacuum soldering processes were compared in terms of void content, shear strength, and microstructure. Results showed that the hot air reflow soldering process exhibited a stable joint with a void content of 5% or less, and the vacuum soldering condition significantly reduced the void content of the solder joint as the soldering proceeded in a vacuum state. The shear strength of the SAC305 solder joint with the same powder particle size was measured to be greater for the shear strength of the vacuum soldered joint as compared to the reflow process. The vacuum soldering process was effective in removing voids during the void joining process and contributed to an improved joint strength of the solder joint by reducing the void content. When the same soldering process was applied using the 1005 MLCC chip component, the bonding strength of the T4 SAC305 solder was slightly higher than those of the SAC105 and SAC0307 solders. However, the overall initial bonding strengths were similar. The e ffects of Ag content within 0.3-3.0 wt% on the initial bonding strengths of the solders were judged to be the same. Diverse Cu6Sn5, Ag3Sn, (Ni,Cu,Pd)3Sn4, (Cu,Ni)6Sn5, NiP, and Ni3P intermetalli ccompounds (IMCs) were formed at the interfaces between the electroless nickel/electroless palladium/immersion gold finish substrate and SAC solder joint. The IMC types were constant regardless of Ag content and solder type, and the IMCs contributed to the initial solder joint strength.

30 April 2022 in Journal of Welding and Joining
Verified
Journal Article
Open access
PDF file
HLHye-Min Lee
Hye-Min Lee
MKMi Song Song Song Kim
Mi Song Song Song Kim
MKMyeongin Kim
Myeongin Kim
WHWON SIK HONG
WON SIK HONG
To confirm the possibility of simultaneous bonding between Si chip and multilayer ceramic capacitors (MLCCs), vacuum reflow soldering is performed between a Si chip and each of 2012, 1608, 1005, 0603, and 0402 MLCCs using Type-7 Sn-3.0Ag-0.5Cu (SAC305) and Sn-0.7Cu solder pastes. To enable an unbiased comparison with the vacuum reflow process, the Si chip and MLCCs are bonded via thermo-compression (TC) bonding and hot air reflow soldering, respectively. The maximum void content of Si chip solder joints bonded via vacuum reflow is 8%. At the MLCC solder joints, the void content yielded by vacuum reflow is lower than that yielded by hot air reflow. The bonding strength of the MLCC solder joint afforded by vacuum reflow is higher than that afforded by hot air reflow. Vacuum reflow is superior to hot air reflow in terms of the void content and bonding strength of the MLCC solder joint. After performing a thermal cycle test (TCT), a crack appeared at the Si chip solder joint bonded by TC bonding. The Cu pillar/Sn-2.5Ag bump is susceptible to cracks after the TCT owing to the insufficient bonding layer thickness yielded; however, the SAC305 sample from vacuum reflow is stable. Meanwhile, (Cu,Ni)6Sn5, Ni3P, and Ag3Sn intermetallic compounds are formed at the MLCC solder joints and then further developed after the TCT. The results of this study indicate the possibility of co-bonding Si chip with MLCCs for semiconductor packaging.

30 June 2022 in Journal of Welding and Joining
Verified
Journal Article
Open access
PDF file
MKMyeongin Kim
Myeongin Kim
WHWON SIK HONG
WON SIK HONG
MKMi Song Song Song Kim
Mi Song Song Song Kim
In this study, the laser soldering process of probe-multilayer ceramic (MLC) substrates was optimized using Type 4 (T4) and Type 7 (T7) Sn-3.0Ag-0.5Cu (SAC305), T7 Sn-0.7Cu solders to improve the high-temperature durability of probe solder joints and satisfy the fine pitch requirements of the soldering process. Thermal cycle tests (TCTs) were performed to compare the heat resistance characteristics of the probe solder joint. The results showed that the bonding strength degradation rates of the SAC305 and Sn-0.7Cu solders after the TCT were within 40% compared to that of the as-soldered state. Because the probe surface and MLC were plated with Ni/Au, various intermetallic compounds (IMCs) were observed at the solder joint. The total IMC thickness of the T7 solder joint was thinner than that of the T4 solder because of the difference in redox reactions according to the particle size of the solder paste. The fracture surface of the probe-MLC solder joint after the shear strength test exhibited a mixed ductile and brittle fracture, and that of the Sn-0.7Cu solder joint exhibited a ductile fracture with numerous dimples.

30 August 2021 in Journal of Welding and Joining
Verified
Journal Article
Open access
PDF file
WHWON SIK HONG
WON SIK HONG
MKMi Song Song Song Kim
Mi Song Song Song Kim
MKMyeongin Kim
Myeongin Kim
SYSang-Hyuk Yun
Sang-Hyuk Yun
YPYunhwi Park
Yunhwi Park
In this study, the laser soldering process of microelectromechanical system (MEMS) probes and multilayer ceramic (MLC) substrates was optimized with Type 4 (T4) and Type 7 (T7) Sn-3.0Ag-0.5Cu (SAC305), Type 4 Sn-0.3Ag-0.7Cu (SAC0307), and Type 4 Sn-5.0Sb (SnSb) soldering, and the probe solder joint properties were compared. SAC0307 and SnSb were used to confirm the bonding property of the low-Ag solder and the high-temperature durability. We conducted a thermal cycling test (TCT) with 500 cycles at temperatures of -25 ℃ to 105 ℃ with a 10-min dwell time at each temperature. Before and after the TCT, the microstructure of solder joint as well as the shear strength between the probe and the MLC were examined. The results revealed that, after the TCT, the degradation rate of T7 SAC305 solder was lower than that of T4 SAC305, and the SnSb solder did not exhibit bonding strength degradation. The fracture mode of the SAC solder joint was ductile-brittle. In the case of the SnSb joint, brittle fracture was the major fracture mode because of the Sn-Sb intermetallic compounds. The SnSb solder had an excellent bonding strength and degradation property after the TCT, but the lack of toughness caused brittle fracture. These results confirm the applicability of T4 SnSb and T7 SAC305 solders for high-temperature response and fine pitch bonding.

30 June 2022 in Journal of Welding and Joining
Verified
Journal Article
Open access
PDF file
MKMi Song Song Song Kim
Mi Song Song Song Kim
WHWON SIK HONG
WON SIK HONG
HLHye-Min Lee
Hye-Min Lee
MKMyeongin Kim
Myeongin Kim
In this study, the degradation characteristics of solder joints composed of powder-size Sn-3.0Ag-0.5Cu and the substrate surface finish are compared. Reflow is performed at a N2 ambient to apply an organic solderability preservative (OSP), electroless nickel/immersion gold (ENIG) substrates, and solder pastes of Type 6 (5-15 ㎛) and Type 7 (2-11 ㎛). Subsequently, a thermal shock test (TST) is performed for 1,500 cycles at a temperature of -40 ℃ to 125 ℃ (dwell time of 10 min) to analyze the deterioration characteristics. After N2 reflow is performed, the void content of the OSP substrate/solder joints is higher than that of the ENIG substrate/solder joints, and the shear strength of the ENIG substrate/solder joints is higher than that of the OSP substrate/solder joints. After 500 TST cycles, the shear strength at the OSP substrate/Type 7 solder joints does not decrease, whereas the shear strength at the ENIG substrate/Type 7 solder joints decreases by approximately 25%. Cross-sectional analysis shows that Cu6Sn5 and (Ni,Cu)3Sn4 intermetallic compounds (IMCs) emerged in the OSP and ENIG interfaces, respectively. The increasing rate of IMC thickness at the Type 7 solder joints is higher than that at the Type 6 solder joints. Fracture analysis shows that the OSP and ENIG joints fractured in the solder and solder/IMC interfaces, respectively. The IMC of the OSP and ENIG joints exhibit scallop and needle shapes, respectively. The ENIG joints fractured at the solder/IMC interface because of a stress concentration in the needle-type IMC. After 1500 TST cycles, the shear strength of all samples decreases by more than 50%. Cross-sectional analysis shows a crack at the solder joints of all samples after 1,000 cycles. The decrease in shear strength is caused by these cracks.