Yuriy Seregin

Yuriy Seregin

Auto-generated profile, based on publicly available information

Yuriy Seregin

Reshetnev Siberian State University of Science and Technology,Information Control Systems Department,Krasnoyarsk,Russia

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
16 March 2022
Verified
Conference Paper
Closed access
Vadim TynchenkoVadim Tynchenko
Vadim Tynchenko
VBVladimir Bukhtoyarov
Vladimir Bukhtoyarov
DRDaria Rogova
Daria Rogova
AMAleksander Myrugin
Aleksander Myrugin
YSYuriy Seregin
Yuriy Seregin
ABAleksey Bocharov
Aleksey Bocharov
The article develops a software system module for modeling the brazing of spacecraft elements from widely used alloys based on induction heating. The approach proposed by the authors is based on the use of two-dimensional non-stationary heat conduction equations. A permanent heat source is added to these equations, because heating occurs due to eddy currents. The mathematical model proposed by the authors considers: the geometric parameters of the waveguides, the physical parameters of materials, the initial and boundary conditions, as well as the uneven distribution of the eddy current density in the waveguide. This approach allows you to simulate the brazing process for almost any materials with different geometric parameters used in the aerospace industry. In this work, we simulate the process of induction brazing of pipelines from Alloy 321 stainless steel (UNS S32100). The need to develop a module of the software system is due to: (1) high temperature of the board and the need to withstand the regime; (2) use of duct boxes to create a protective environment; (3) high material costs when developing a new technological process (for example, when brazing a larger pipe). As a result of this work, a software system module was developed and modeling of induction brazing of pipelines in protective environments from Alloy 321 stainless steel was carried out, the results of which are presented in the article.

16 March 2022
Verified
Conference Paper
Closed access
SKSergei Olegovich Kurashkin
Sergei Olegovich Kurashkin
VBVladimir Bukhtoyarov
Vladimir Bukhtoyarov
AMAleksander Myrugin
Aleksander Myrugin
ABAleksey Bocharov
Aleksey Bocharov
YSYuriy Seregin
Yuriy Seregin
DRDaria Rogova
Daria Rogova
The setting of technological parameters, in particular the beam current and speed in electron beam welding, are an integral part of the process. However, to set the mode when welding a new product or changing equipment (for example, buying a new installation or replacing an electron-beam gun or a drive for rotating a turntable), it is currently necessary to search for technological parameters (welding speed, beam current) by carrying out full-scale experiments, which is a resource and financially costly. Thus, in this work, the authors propose to carry out imitation modeling of the process of electron beam welding of a disk with a cylinder made of titanium alloy (Ti-4Al-3Mo-1V) in COMSOL Multiphysics, in order to develop the proposed technology to obtain optimal technological parameters in electron beam welding. thin-walled structures. The structure to be welded consists of two components: a hollow cylinder with a diameter of 78 mm, a height of 80 mm and a disc with a diameter of 76 mm, a thickness of 12 mm with a through hole, the wall thickness of the cylinder along which welding is 3 mm. As a result, the authors carried out modeling and obtained graphs of product heating, which depict the temperature distribution. The mode corresponding to the requirements put forward, the width of the weld 2 mm, the height of the seam 1mm was obtained with the following technological parameters: welding speed 1.2 cm/s, beam current 67 mA, accelerating voltage 30 kV, focusing current 139 mA.


20 February 2022
Verified
Conference Paper
Closed access
RTReshetnev Siberian State University of Science and Technology
Reshetnev Siberian State University of Science and Technology
Vadim TynchenkoVadim Tynchenko
Vadim Tynchenko
SUSiberian Federal University
Siberian Federal University
BUBauman Moscow State Technical University
Bauman Moscow State Technical University
VBVladimir Bukhtoyarov
Vladimir Bukhtoyarov
YSYuriy N. Seregin
Yuriy N. Seregin
An artificial neural network is a system of simple processors (artificial neurons) that are connected and interact with each other. Programming neural networks means training the network, not writing program code. Thanks to training, the network is able to identify dependencies between data (input and output), generalize, simplify the results, and use knowledge to break down complex problems into simpler ones. The aim of the presented work is to improve the efficiency of managing the needs of the clients of the fitness club through the use of modern methods of data analysis. As a technology for the implementation of such an analysis, the work uses neural networks of a special type - Kohonen networks. On the basis of the proposed approach, the final software product is being developed to improve the quality of management of a fitness club.

24 September 2021
Verified
Book Chapter
Closed access
PDF file
SKSergei Olegovich Kurashkin
Sergei Olegovich Kurashkin
Vadim TynchenkoVadim Tynchenko
Vadim Tynchenko
YSYuriy Seregin
Yuriy Seregin
AMAleksandr Murygin
Aleksandr Murygin
ABAleksey Bocharov
Aleksey Bocharov

1 June 2022
Verified
Conference Paper
Closed access
NFNatalia Fedorova
Natalia Fedorova
AMAleksander Myrugin
Aleksander Myrugin
EFElena Filushina
Elena Filushina
YSYuriy Seregin
Yuriy Seregin
EVElena Vaitekunene
Elena Vaitekunene
YDYuriy Danilchenko
Yuriy Danilchenko
The article collected and structured data for regression analysis. The reasons for which cork is formed in the city of Krasnoyarsk were considered. Using the collected data, a primary histogram (not tested for emissions) was constructed. The following factors were identified as relevant and weak-influencing factors for the construction of the correlation table, this table helps to identify the superfluous influence on the formation of traffic jams. Taking into account the table, a new histogram was constructed and a correlation table was created, which allows to start regression analysis. At the beginning of the regression analysis regression statistics are used and the variance analysis is carried out, then the regression analysis is made directly and the regression results are summarized. Based on the summing up of the histogram, which takes into account all statistics and calculations, which reflects the predicted number of traffic jams and the real factors influencing the formation of traffic jams.