18 May 2015 in Nature Nanotechnology
The nanostructuring of silicon surfaces--known as black silicon--is a promising approach to eliminate front-surface reflection in photovoltaic devices without the need for a conventional antireflection coating. This might lead to both an increase in efficiency and a reduction in the manufacturing costs of solar cells. However, all previous attempts to integrate black silicon into solar cells have resulted in cell efficiencies well below 20% due to the increased charge carrier recombination at the nanostructured surface. Here, we show that a conformal alumina film can solve the issue of surface recombination in black silicon solar cells by providing excellent chemical and electrical passivation. We demonstrate that efficiencies above 22% can be reached, even in thick interdigitated back-contacted cells, where carrier transport is very sensitive to front surface passivation. This means that the surface recombination issue has truly been solved and black silicon solar cells have real potential for industrial production. Furthermore, we show that the use of black silicon can result in a 3% increase in daily energy production when compared with a reference cell with the same efficiency, due to its better angular acceptance.
1 February 2016 in Solar Energy Materials and Solar Cells
This work reports on a comparative study comprising three transition metal oxides, MoO3, WO3 and V2O5, acting as front p-type contacts for n-type crystalline silicon heterojunction solar cells. Owing to their high work functions (>5 eV) and wide energy band gaps, these oxides act as transparent hole-selective contacts with semiconductive properties that are determined by oxygen-vacancy defects (MoO3-x), as confirmed by X-ray photoelectron spectroscopy. In the fabricated hybrid structures, 15 nm thick transition metal oxide layers were deposited by vacuum thermal evaporation. Of all three devices, the V2O5/n-silicon heterojunction performed the best with a conversion efficiency of 15.7% and an open-circuit voltage of 606 mV, followed by MoO3 (13.6%) and WO3 (12.5%). These results bring into view a new silicon heterojunction solar cell concept with advantages such as the absence of toxic dopant gases and a simplified low-temperature fabrication process.Preprin
19 December 2016 in Journal of Materials Research
1 August 2017 in Solar Energy Materials and Solar Cells
Transition metal oxides (TMOs) have recently been proved to efficiently serve as hole-selective contacts in crystalline silicon (c-Si) heterojunction solar cells. In the present work, two TMO/c-Si heterojunctions are explored using MoO3 (reference) and V2O5 as an alternative candidate. It has been found that V2O5 devices present larger (16% improvement) power conversion efficiency mainly due to their higher open-circuit voltage. While V2O5/c-Si devices with textured front surfaces exhibit larger short-circuit currents, it is also observed that flat solar cell architectures allow for passivation of the V2O5/n-Si interface, giving significant carrier lifetimes of 200 µs (equivalent to a surface recombination velocity of Seff ~140 cm s-1) as derived from impedance analysis. As a consequence, a significant open-circuit voltage of 662 mV is achieved. It is found that, at the TMO/c-Si contact, a TMO work function enhancement ¿FTMO occurs during the heterojunction formation with the consequent dipole layer enlargement ¿’=¿+¿FTMO. Our results provide new insights into the TMO/c-Si contact energetics, carrier transport across the interface and surface recombination allowing for further understanding of the nature of TMO/c-Si heterojunctions.Peer ReviewedPostprint (published version
1 October 2001 in Applied Physics Letters
Excellent passivation properties of intrinsic amorphous silicon carbide films deposited by plasma enhanced chemical vapor deposition on single-crystalline silicon wafers have been obtained. The dependence of the effective surface recombination velocity, on deposition temperature, total pressure and methane to silane ratio has been studied for these films using lifetime measurements made with the quasi-steady-state photoconductance technique. The dependence of the effective lifetime, on the excess carrier density, has been measured and also simulated through a physical model based on Shockley–Read–Hall statistics and an insulator/semiconductor structure with fixed charges and band bending. A at the interface lower than was achieved with optimized deposition conditions. This passivation quality was found to be three times better than that of noncarbonated amorphous silicon films deposited under equivalent conditions.