Artificial synapses, inspired by the intricate design of biological synapses, utilize electrical, chemical, and mechanical signals to transmit and retain information. Recent advances have involved research on artificial synapses based on organic electrochemical transistors (OECTs), emphasizing low power consumption and rapid response times. A notable challenge arises when the gate voltage is removed, causing doped ions to return quickly to the electrolyte. A simple yet efficient approach is used to solve this problem: forming a microporous active layer using a phase separation method. This technique can maximize the contact area between the electrolyte and the active layer, enhancing ion doping/de‐doping in OECTs. Improvements in the product of hole mobility and volumetric capacitance is achieved. The electrostatic coupling effect and electrochemical doping in synaptic OECTs occur better than in the pristine active layer, yielding enhanced performance with higher short‐term and long‐term synaptic plasticity, compared to pristine OECTs. Moreover, improved ambipolar characteristics is shown by n‐dopant injection. This paper reports a way to improve performance by simply modifying the surface shape of the active layer using the phase separation, contributing to advancements in artificial synapses for neural networks.
A dual-gate configuration has been introduced to organic thin-film transistors (TFTs) for full-depletion behavior to enhance the transconductance, subthreshold slope, and drain current on-off ratio. In this letter, we show how those dual-gate effects influence the static and dynamic responses of three-dimensional (3-D) complementary organic logic gates in comparison to their single-gate counterpart. For the comparative study, 3-D inverters and ring oscillators were fabricated by printing directly on plastic foil in both single-and dual-gate configurations. In the static inverter operation, the fully depleted characteristics of the dual-gate TFTs lead to an increase in voltage gain and a dramatic decrease in standby power consumption. In the dynamic ring oscillator operation, the two configurations have comparable gate delays because the use of an additional gate increases not only the drain current but also the load input gate capacitance. Our findings demonstrate the performance of an inverter that can represent the overall operation of complementary logic gates consisting of pull-up and pull-down networks, thereby providing significant insight into printed organic TFT circuit design using dual gating effects.
Direct printing of conjugated polymer thin‐film transistors enables the fabrication of deformable devices with low cost, high throughput, and large area. However, a relatively poor device performance of printed devices remains a major obstacle to their application in high‐end display backplanes and integrated circuits. In this study, high‐performance and highly stackable printed organic transistors is developed, arrays, and circuits using a near‐amorphous polymer, indacenodithiophene‐co‐benzothiadiazole (IDT‐BT). The printed devices exhibited high saturation mobility (>1 cm2 V−1 s−1), high on/off ratio (>107), and low subthreshold slope (245 mV dec−1). In addition, 16 × 16 printed IDT‐BT arrays achieved 100% fabrication yield, with excellent device‐to‐device uniformity and low variations of mobility (9.55%) and threshold voltage (4.51%), and good operational and environmental stability (>365 days). Furthermore, five stacked 3D transistors are demonstrated with an excellent 3D uniformity without compromising device performance due to a low required thermal budget for processing amorphous IDT‐BT. Finally, a new concept of 3D universal logic gate with high voltage gain (33.91 V/V) and record density (100 printed transistors per cm2) is proposed and fabricated, which is relevant for the commercialization of low‐cost printed display backplanes and high‐density integrated circuits based on highly processable polymeric semiconductors.
A three-dimensional (3-D) and printed static random-access memory (SRAM) based on complementary organic thin-film transistors is demonstrated. The SRAM exhibited the smallest area of 2.1 mm 2 , the highest normalized static noise margin of 62%, and the maximum gain of 16.8 V/V compared to the reported values of organic SRAM cells. The transistors’ 3-D integration minimizes the cell area. The 3-D SRAM cell design enables us to match the strengths of transistors by modifying the dielectric thickness without changing the channel geometry. This high-performance complementary organic thin-film transistors-based SRAM shows its high application potential in large-scale and low-cost wearable intelligent electronics for data storage and processing.