24 March 2021 in IEEE Transactions on Plasma Science
Grading capacitors are required to balance the voltage distribution of the double-break vacuum circuit breaker. However, large grading capacitors increase the magnitude and duration of the reignition current. To reduce grading capacitors, a synthetic circuit with double vacuum breaks was set up to study the effects of arcing time on voltage distribution. The voltage distribution of the upper break decreases from 61% to 52% with arcing times of two breaks decreasing from 6.6 to 3.4 ms synchronously. The experimental results demonstrate that reducing the arcing times can balance the voltage distribution during the transient recovery voltage (TRV) rising phase. The unbalance of TRV distribution can be further improved by adopting appropriate arcing times in the two breaks with grading capacitors having a capacitance of 3000 pF.
29 December 2021 in IEEE Transactions on Plasma Science
Surface flashover triggered vacuum switch (STVS) working performance mainly depends on the electrical characteristics of trigger pulse. This article presents an experimental investigation of the trigger process. The influence of the electrical properties of the trigger pulse on the trigger characteristics is focused. Based on the self-developed high-performance STVS product, the experimental test platform was established. The experimental results show that a shorter delay time of STVS can be obtained by heightening trigger voltage. However, the effect of trigger voltage on time jitter is not obvious. The slight increase in trigger current has evident influence on trigger delay time. It also does not affect the stability of trigger delay. With the increase in trigger voltage rise rate, the trigger delay time and time jitter can be optimized. Finally, the long-term stability of STVS is discussed. After 300 trigger times, the delay time changes from about 140 ns to more than 150 ns and the jitter changes from about 5 ns to more than 10 ns. In the design of STVS products, it is recommended to adopt a trigger system with a fast rise rate of trigger voltage and trigger current.
18 June 2019 in IEEE Transactions on Plasma Science
Working performances of laser-triggered vacuum switch (LTVS) mainly rely on the interactions of laser with target materials. Influences from target configuration, which is one of key factors in the interactions, are neglected so far. The trigger performances of LTVS with different target configurations are studied in this paper. Relevant influence factors about target configurations are discussed briefly based on theoretical analysis about the trigger process. The test prototype is established based on detachable vacuum chamber. The trigger characteristics of LTVS with different target structures, target depths, and laser focal positions are compared. The relationships between target configurations and trigger performances of LTVS are analyzed and discussed. The preferred targets in LTVS are suggested while considering its lifetime. The test results prove that the conical target shows the best trigger performances compared to other targets. Due to the enlarged laser irradiated area and shortened plasma moving distance, the delay time of LTVS reduces with the decrease in conical target angle and the increase in target depth, while the delay time is controlled within 32 ns. Benefited from laser reflection and plasma collision, the trigger performances of conical targets can be enhanced by focusing laser on the target side surface. In particular, the 90° conical target with 1.5 mm depth is suggested to be employed in LTVS products.
1 March 2024 in Physics of Fluids
The deicing process and its status characteristics of dual-side pulsed surface dielectric barrier discharge (SDBD) are studied via electro-optical diagnostics, thermal properties, and numerical simulation. Experimental results show that the dual-side pulsed SDBD can remove the glaze ice compared to the traditional pulsed SDBD under the applied pulse voltage of 8 kV and a pulse frequency of 1 kHz. The maximal temperature of dual-side pulsed SDBD reaches 39.5 °C under the discharge time of 800 s, while the maximal temperature of traditional pulsed SDBD is still below ice point about −7.8 °C. Surface temperatures of dual-side pulsed SDBD demonstrate that the SDBD with a gap of 1 mm possesses prospects in deicing. The maximal surface temperature reaches 37.1 °C under the pulse of 8 kV after the discharge time of 90 s. Focusing on the thermal effect, a two-dimensional plasma fluid model is implemented, and the results also indicate that the dual-side pulsed SDBD with a gap of 1 mm produces a highest heat density among the three different configurations. Comparing the spatial-temporal evolutions of plasma on both dielectric sides, primary positive streamer has a longer propagation length of 8.6 mm than the secondary negative streamer, the primary negative streamer, and the secondary positive streamer, which induces a long heat covered area. Four stages of deicing process are analyzed through a series of electrical parameters under different covered ice conditions.
30 September 2024 in Applied Physics Letters
A coplanar-volume coupled discharge utilizing a capillary coplanar dielectric barrier discharge (CDBD) as a pre-ionization source and employing a negative direct current (DC) voltage to prompt plasma propagation from the dielectric surface to the air gap is proposed and experimentally investigated. Optical-electrical properties, spatial-temporal evolution of plasma, and active species generation are systematically studied to provide in-depth insights into the plasma characteristics of coplanar-volume coupled discharge based on pre-ionization. Compared to traditional dielectric barrier discharge, this approach reduces the inception voltage and significantly enhances the discharge intensity. Spatial-temporal evolution of plasma morphology demonstrates two distinct discharge processes occurring in coplanar-volume coupled discharge: coupled primary discharge and coupled secondary discharge. These processes are developed from the coplanar primary discharge and coplanar secondary discharge in capillary CDBD, respectively. Through analyzing the effects of pulse voltage and negative DC voltage on the physical and chemical properties of plasma, coplanar-volume coupled discharge based on high pre-ionization exhibits strong plasma luminous intensity, elevated discharge energy, and heightened chemical activity.
27 April 2020 in IEEE Transactions on Plasma Science
The electrode configurations have an important effect on the interruption performances of laser triggered vacuum switch (LTVS), but few works pay attention to it so far. The objective of this article is to study the interruption capacity of LTVS with different electrode configurations. The 3-D simulation models of axial magnetic field (AMF) electrode and transverse magnetic field (TMF) electrode are built up, and the magnetic field distributions are calculated and compared. The test platform is set up based on a detachable vacuum chamber. The interruption capacity of LTVS with different electrode structures, electrode spacings, and polarity configurations is studied and analyzed. The test results prove that, compared to the AMF electrode, the interruption capacity of LTVS under the TMF electrode is obviously better, but it is more susceptible to the electrode spacing, and gradually decreases with the increase of electrode spacing. Influence of polarity configuration on the interruption capacity of LTVS is closely related to the target material. The LTVS with KCl + Ti under the positive polarity configuration shows better interruption capacity than negative polarity configuration. The works in this article provide references for the design of LTVS products.