Jonas Huether

Jonas Huether

Auto-generated profile, based on publicly available information

Jonas Huether

Institute for Applied Materials IAM-WK, Karlsruhe Institute of Technology, Engelbert-Arnold-Straße 4, Karlsruhe, Baden-Württemberg, 76131, GERMANY

Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 July 2016 in IOP Conference Series: Materials Science and Engineering
Verified
Conference Paper
Open access
PDF file
JHJonas Hüther
Jonas Hüther
PBPovl Brøndsted
Povl Brøndsted
During the manufacturing process of fiber reinforced polymers the curing reaction of the resin results in shrinkage of the resin and introduces internal stresses in the composites. When curing at higher temperatures in order to shorten up the processing time, higher curing stresses and thermal stresses are built up and frozen, as residual stresses occur. In the present work, a glass fiber reinforced epoxy composite laminate with an unidirectional architecture based on non-crimp fabrics with backing fibers is investigated. Three different curing cycles (timetemperature cycles) are used, leading to different levels of internal stresses. The mechanical properties, static strength and fatigue life time, are measured in three different directions of the material, i.e. the fiber direction, 0 • , the 30 • off axis direction, and the 90 • direction transverse to the fiber direction. It is experimentally demonstrated that the resulting residual stresses barely influences the quasi-static mechanical properties of reinforced glass-fiber composites. It is found that the fatigue performance in the 0 • direction is significantly influenced by the internal stresses, whereas the fatigue performance in the off axes directions so is not significantly influenced of these stresses. This is related to the observations that the damage mechanisms in the off axes directions are mainly related to shear failure in the matrix and in the interface between fiber and matrix and different from the damage mechanisms in the fiber direction, where the damage initiates in the transverse backing fibers and is directly related to fiber fractures in the load-carrying axial fiber bundles.

7 March 2018 in Measurement Science and Technology
Verified
Journal Article
Closed access
PDF file
JHJonas Huether
Jonas Huether
PRPeter Rupp
Peter Rupp
IKIna Kohlschreiber
Ina Kohlschreiber
KWKay André Weidenmann
Kay André Weidenmann
To obtain mechanical tensile properties of materials it is customary to equip the specimen directly with a device to measure strain and Young’s modulus correctly and only within the measuring length defined by the standards. Whereas a variety of tools such as extensometers, strain gauges and optical systems are available for specimens on coupon level, no market-ready tools to measure strains of single fibres during single fibre tensile tests are available. Although there is a standard for single fibre testing, the procedures described there are only capable of measuring strains of the whole testing setup rather than the strain of the fibre. Without a direct strain measurement on the specimen, the compliance of the test rig itself influences the determination of the Young’s modulus. This work aims to fill this gap by establishing an enhanced method to measure strains directly on the tested fibre and thus provide accurate values for Young’s modulus. It is demonstrated that by applying and then optically tracking fluorescing polymeric beads on single glass fibres, Young’s modulus is determined directly and with high repeatability, without a need to measure at different measuring lengths or compensating for the system compliance. Employing this method to glass fibres, a Young’s modulus of approximately 82.5 GPa was determined, which is in the range of values obtained by applying a conventional procedure. This enhanced measuring technology achieves high accuracy and repeatability while reducing scatter of the data. It was demonstrated that the fluorescing beads do not affect the fibre properties.

21 December 2021 in Manufacturing Review
Verified
Journal Article
Open access
PDF file
AHAnselm Heuer
Anselm Heuer
JHJonas Huether
Jonas Huether
WLWilfried Liebig
Wilfried Liebig
PEPeter Elsner
Peter Elsner
The mechanical properties of plastic-based additively manufactured specimens have been widely discussed. However, there is still no standard that can be used to determine properties such as the interfacial strength of adjacent tracks and also to exclude the influence of varying manufacturing conditions. In this paper, a proposal is made to determine the interfacial strength using specimens with only one track within a layer. For this purpose, so-called single-wall specimens of polylactide were characterised under tensile load and the interfacial area between the adjacent layers was determined using three methods. It turned out that the determination of the interfacial area via the fracture surface is the most accurate method for determining the interfacial strength. The measured interfacial strengths were compared with the bulk material strength and it was found that the bulk material strength can be achieved under optimal conditions in the FFF process. It was also observed that with increasing nozzle temperature, the simultaneous printing of specimens influences the interfacial strength. To conclude, this method allows to measure the interfacial strength without superimposing the influence of voids. However, for example, the interfacial strength within a layer cannot be determined.

9 January 2019 in Measurement Science and Technology
Verified
Journal Article
Closed access
PDF file
JHJonas Huether
Jonas Huether
DEDaniel Esse
Daniel Esse
PRPeter Rupp
Peter Rupp
MSMichael Seitz
Michael Seitz
KWKay André Weidenmann
Kay André Weidenmann
The Young's modulus of single carbon fibres, virgin and recycled, is investigated in this study. Single fibre measurements are enhanced in two fields: Firstly, the cross-sectional area is calculated by taking individual measurements with a laser dffraction sensor and applying a sinusoidal fit to account for irregular fibre shapes. Secondly, strains during the loading cycle are measured directly by applying fluorescing tracking markers on the fibre and using one-dimensional digital image correlation. Several markers are applied on each side of the fibre to allow for a statistically verified evaluation. To achieve high-resolution images, a step-wise load cycle is applied. The load is increased in steps of 250MPa until finale failure. It is demonstrated that direct strain measurement and enhanced determination of the Young's modulus are possible for carbon fibres. It was further shown that the recycling of the carbon fibre by pyrolysis reduced the Young's modulus by approximately 10 % compared to virgin fibres.