Anfeng Huang

Anfeng Huang

Auto-generated profile, based on publicly available information

Anfeng Huang

EMC Laboratory, Missouri University of Science and Technology, Rolla, MO, USA

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 July 2020
Verified
Conference Paper
Closed access
AHAnfeng Huang
Anfeng Huang
XYXin Yan
Xin Yan
JSJingdong Sun
Jingdong Sun
QHQiaolei Huang
Qiaolei Huang
JFJun Fan
Jun Fan
ZYZhiping Yang
Zhiping Yang
In modern mobile electronic systems, USB connector has been identified as one of the dominant noise sources for desense issues. In this paper, the noise coupled to the Wi-Fi antenna from a USB connector is investigated. With the assistance of full-wave simulations, the root cause of desense noise is identified as the non-ideal electrical connection between the metal chassis and the USB receptacle shell where it is installed. The proposed radiation mechanism is validated through measurements of a real tablet device, and 15 dB noise level reduction is observed with a better grounding structure.

23 March 2023 in IEEE Transactions on Electromagnetic Compatibility
Verified
Journal Article
Closed access
AHAnfeng Huang
Anfeng Huang
JSJingdong Sun
Jingdong Sun
HKHONGSEOK KIM
HONGSEOK KIM
ZXZhenxue Xu
Zhenxue Xu
SJShuai Jin
Shuai Jin
CHChulsoon Hwang
Chulsoon Hwang
Accurate evaluation and simulation of power noise is critical in the development of modern electronic devices. However, the widely used target impedance fails to predict the low-frequency noise generated in a device due to the existence of the dc–dc converter, whose output impedance can change under different loading conditions. A physical circuit model is then desired to replicate the behavior of a voltage regulator module, and the average technique is an efficient method to estimate the noise of a pulsewidth-modulated (PWM) converter. With the emergence of converters with adaptive on-time (AOT) controllers, more complex averaging methods are required, but none of them supports transient simulation. A general, efficient, and accurate modeling technique is presented in this article, whose framework supports both current-mode PWM and AOT controllers. In addition, a novel two-step parameter extraction method is proposed, which can be used to evaluate the equivalent values of internal feedback parameters of an encrypted simulation model or from measurement. The modeling method is validated by both simulation and measurement.

1 February 2022 in Review of Scientific Instruments
Verified
Journal Article
Closed access
PDF file
AHAnfeng Huang
Anfeng Huang
JFJun Fan
Jun Fan
CHChulsoon Hwang
Chulsoon Hwang
Accurate core-loss characterization is essential to push the power density of power converters to their limits. However, existing core-loss measurement methods still have some limitations, such as a slow test speed and a complex probe calibration procedure. In particular, accurate phase-difference measurement is time-consuming because a fast Fourier transform analysis with a kHz-range frequency interval is typically applied to reduce the influence of noise. An automated measurement system for magnetic core-loss characterization is described in this paper. An accurate phase-detection block with programmable attenuators is developed to measure the phase difference between voltage and current waveforms. The proposed system considerably improves the test speed while providing comparable accuracy to the existing method.

26 July 2021
Verified
Conference Paper
Closed access
AHAnfeng Huang
Anfeng Huang
JSJingdong Sun
Jingdong Sun
HKHONGSEOK KIM
HONGSEOK KIM
JFJun Fan
Jun Fan
ZXZhenxue Xu
Zhenxue Xu
CHChulsoon Hwang
Chulsoon Hwang
Proper power integrity (PI) analysis is essential for modem electronics devices to minimize voltage noise. The low- frequency response of a power distribution network (PDN) is determined by the voltage regulator modules (VRMs) installed on the board. However, the conventional VRM model is either represented by an over-simplified passive circuit or an encrypted model provided by then vendor. These models can only work for limited operating conditions. In this paper, a generic average model for up-to-date DC converter is proposed. Both time and frequency domain responses of a current-mode buck converter with adaptive on-time control (AOT) method are captured by the proposed model. This cycle-by-cycle averaged model can be extended for converters with other control methods.

1 January 2026 in IEEE Transactions on Electromagnetic Compatibility
Verified
Journal Article
Closed access
YZYukui Zhou
Yukui Zhou
AHAnfeng Huang
Anfeng Huang
HLHuimin Liao
Huimin Liao
BWBoda Wang
Boda Wang
JFJun Fan
Jun Fan
JHJunping He
Junping He

13 April 2026 in IEEE Transactions on Electromagnetic Compatibility
Verified
Journal Article
Closed access
QHQiusen He
Qiusen He
AHAnfeng Huang
Anfeng Huang
CLChenxi Liu
Chenxi Liu
JLJie Luo
Jie Luo
ZGZhitong Guo
Zhitong Guo
XSXinglin Sun
Xinglin Sun
Magnetic shielding sheets in wireless power transfer (WPT) systems exert a critical influence on both energy transfer efficiency and electromagnetic compatibility (EMC) performance. Commonly used high-performance layered nanocrystalline shielding sheets exhibit notable discrepancies between the effective permeability of their layered structures and the intrinsic permeability of the nanocrystalline flake ribbon materials. The design of their stacking critically determine the equivalent permeability of these shielding sheets. The precise characterization of permeability in layered nanocrystalline shielding sheets presents a challenge, which limits the accuracy of performance simulations in WPT systems. In addition, in recent widely used magnetic snap-on WPT applications, inadequate permanent magnet design can lead to the saturation of permeability in layered nanocrystalline shielding sheets, severely hindering power transfer efficiency. This study proposes an efficient method for rapid permeability characterization of layered nanocrystalline shielding sheets, solving the permanent magnet-influenced WPT challenge and preventing nanocrystalline saturation from bad permanent magnet design of magnetic snap-on WPT application.