24 August 2021 in IEEE Sensors Journal
The temperature-dependent polarization induced bias drift is a major factor affecting the long-term zero-bias stability of integrated optic gyro (RIOG). The silicon nitride (Si 3 N 4 ) with high-aspect-ratio core geometry allows high polarization extinction ratio and ultra-low propagation loss. We start from suppressing the polarization noise of the RIOG and design a single polarization Si 3 N 4 waveguide ring resonator (WRR) with a radius of 17.5 mm. We established the polarization model of the WRR. It is found through simulation that when the polarization-dependent loss of the Si 3 N 4 waveguide reaches 800 dB/m, it can maintain the single-polarization performance, thereby suppressing the polarization noise of the gyroscope. And the relationship between the coupling coefficient of the coupler and the limit sensitivity, finesse and transmittance was determined. The cross-sectional size of the Si 3 N 4 WRR is determined to be $4\,\,\mu \text{m}\,\,\times 40$ nm simultaneously by simulation. Finally, through its processing and testing, a single-polarization WRR with a finesse of 127, the quality factor is $1.31\times 10 ^{7}$ , a transmission loss of 2.5 dB/m, and a polarization-dependent loss of 810 dB/m is obtained. Meanwhile, we prove its single-polarization performance at different temperature. The successful design and fabrication of the WRR is expected to achieve high precision RIOG.
28 September 2021 in Journal of Lightwave Technology
This paper proposes a fiber length matching method that reduces the influence of Fresnel reflection in a hybrid fiber resonator for the resonant fiber optic gyroscope (RFOG). A transfer model of the fused points inside and outside the fiber resonator is first built. Using the transfer model, we find that when the optical path ratio of the photonic bandgap fiber (PBF) is half of the entire fiber ring, the secondary resonant frequency points caused by Fresnel reflection coincide with the main resonant frequency points of the resonator, and the resonant depth becomes equal. The simulation result of the resonance curve demonstrates this theory. To validate our deduction, two hybrid resonators are obtained with PBF and polarization-maintaining fiber (PMF). The optical path ratio of one resonator is 0.5, and the other is approximately 0.2. The results show that after the fiber length matching, the resonance depth difference of the resonator is less than 1.8%, which is the best reported index of a fused PBF fiber resonator to our knowledge and 24.9% less than that of the other resonator. The experimental result also shows that the total loss of the two PBF-PMF fused points is less than 1.3 dB. Our scheme effectively reduces the effect of the Fresnel reflection at the fusing point in the PBF-PMF resonator, which is expected to achieve accurate resonance frequency detection of the RFOG.
16 November 2021 in Journal of Lightwave Technology
Backscattering noise is a key factor to restrict the performance of resonant fiber optic gyroscopes (RFOG). In order to improve the accuracy of RFOG, this paper proposes a scheme with heterodyne optical phase-locked loop (HOPLL) technique based on acousto-optic modulation (AOM) to suppress backscattering noise. In this scheme, the main light source is divided into three output lights, two of which are frequency-shifted by the AOM, and then are phase-locked with the third light, using the HOPLL technique. The two channels of frequency-shifted light are respectively used as the clockwise (CW) and counterclockwise (CCW) light of the RFOG, and are locked on the resonance peak. The transmissive fiber resonator can be regarded as a band-pass filter. By adjusting the reference signal in the HOPLL, the carrier of the two frequency-shifted lights can be moved away from the resonance peak. The carrier light intensity of the frequency-shifted light is suppressed by the cavity itself. The suppression ratio (SPR) reaches 15.83dB. The experimental results illustrate that the bias stability of RFOG is 3.8°/h based on the Allan deviation, strongly proving the effectiveness of this scheme in suppressing backscattering noise in practical applications.
11 May 2020 in IEEE Sensors Journal
A real-time free spectral range (FSR) measurement system based on heterodyne optical phase-locked loop (HOPLL) is proposed for the first time to test the FSR of a fiber resonator. In this system, HOPLL is used to lock phase between the master and slave lasers, so that the frequency difference between them reach one FSR. In addition, PDH technique is used to establish a resonant tracking loop. By setting the loop control parameters, the master and slave lasers are respectively locked on two adjacent resonance peaks of the cavity. If the ambient temperature changes, the cavity length of the resonant cavity will change accordingly. Then the real-time change of FSR of the resonant cavity can be measured by detecting feedback change of the loop. The experimental results show that the linewidth of beat signal of the master and slave lasers after phase-locking is less than 10Hz, and also the frequency noise of the 10Hz bandwidth is 0.0154Hz which is 60dB lower than that before phase-locking. The researchers find that the FSR coefficient of thermal expansion is -210.35±0.15Hz/°C, which is consistent with theoretical results. The relative measurement accuracy of 1.5×10-9 is achieved in this loop. Therefore, the experimental results effectively verify the actual application performance of the real-time FSR measurement based on HOPLL technique.
24 July 2021 in Pituitary
1 October 2025 in Journal of Systems Engineering and Electronics
A high precision detection technique is analyzed based on the optical micro electro-mechanical system (MEMS) accelerometer with double gratings for noise suppression and scale factor enhancement. The brief sensing model and modulation detection model are built using the phase sensitive detection, and the relationship between stimulated acceleration and system output is given. The schematics of gap modulation and light intensity modulation are analyzed respectively, and the choice of modulation frequency in the optical MEMS accelero-meter system is discussed. According to the experimental results, the scale factor is improved from 15.45 V/g with the gap modulation to 18.78 V/g with the light intensity modulation, and the signal to noise ratio is improved from 42.95 dB to 81.73 dB. The overall noise level in the optical MEMS accelerometer is effectively suppressed.