Lab scale additive manufacturing of Fe-Nd-B based powders was performed to realize bulk nanocrystalline Fe-Nd-B based permanent magnets. For fabrication a special inert gas process chamber for laser powder bed fusion was used. Inspired by the nanocrystalline ribbon structures, well-known from melt-spinning, the concept was successfully transferred to the additive manufactured parts. For example, for Nd16.5-Pr1.5-Zr2.6-Ti2.5-Co2.2-Fe65.9-B8.8 (excess rare earth (RE) = Nd, Pr; the amount of additives was chosen following Magnequench (MQ) powder composition) a maximum coercivity of µ0Hc = 1.16 T, remanence Jr = 0.58 T and maximum energy density of (BH)max = 62.3 kJ/m3 have been achieved. The most important prerequisite to develop nanocrystalline printed parts with good magnetic properties is to enable rapid solidification during selective laser melting. This is made possible by a shallow melt pool during laser melting. Melt pool depths as low as 20 to 40 µm have been achieved. The printed bulk nanocrystalline Fe-Nd-B based permanent magnets have the potential to realize magnets known so far as polymer bonded magnets without polymer.
The degradation of lithium-ion cells is an important aspect, not only for quality management, but also for the customer of the application like, e.g., scooters or electric vehicles. During the lifetime of the system, the overall health on the battery plays a key role in its depreciation. Therefore, it is necessary to monitor the health of the battery during operation, i.e., cycle life, but also during stationary conditions, i.e., calendar aging. In this work, the degradation due to calendar aging is analyzed for six different cell chemistries in terms of capacity degradation and impedance increase and their performance are being compared. In a new proposed metric, the relative deviations between various cells with the exact identical aging history are being analyzed for their degradation effects and their differences, which stands out in comparison to similar research. The capacity loss was found to be most drastic at 60 °C and at higher storage voltages, even for titanate-oxide cells. LiNiMnCoO2 (NMC), LiNiCoAlO2 (NCA) and Li2TiO3 (LTO) cells at 60 °C showed the most drastic capacity decrease. NMC and NCA cells at 60 °C and highest storage voltage did not show any open circuit voltage, as their current interrupt mechanism triggered. The effect of aging shows no uniform impact on the changes in the capacity variance when comparing different aging conditions, with respect to the evaluated standard deviation for all cells. The focus of this work was on the calendar aging effect and may be supplemented in a second study for cyclic aging.
24 July 2014 in Physica Status Solidi (RRL) – Rapid Research Letters
Permanent magnets based on FePrCuB were realized on a laboratory scale through additive manufacturing (laser powder bed fusion, L-PBF) and book mold casting (reference). A well-adjusted two-stage heat treatment of the as-cast/as-printed FePrCuB alloys produces hard magnetic properties without the need for subsequent powder metallurgical processing. This resulted in a coercivity of 0.67 T, remanence of 0.67 T and maximum energy density of 69.8 kJ/m3 for the printed parts. While the annealed book-mold-cast FePrCuB alloys are easy-plane permanent magnets (BMC magnet), the printed magnets are characterized by a distinct, predominantly directional microstructure that originated from the AM process and was further refined during heat treatment. Due to the higher degree of texturing, the L-PBF magnet has a 26% higher remanence compared to the identically annealed BMC magnet of the same composition.
Highest performance Fe-Nd-B-based permanent magnets offer only low cost-effectiveness and shortened lifetime, both induced by their rare-earth (RE) content. Thus, the necessity for novel hard magnetic phases with better available RE metals, reduced RE content or fully free of RE is immense. As the number of so far unexplored alloy systems is large, the chances that such magnet materials still exist are good. The successful search for novel hard magnetic phases demands an efficient approach of restricting and prioritizing the search field as well as deployment of efficient synthesis and analysis methods.
The TM14RE2B-based phases (TM = transition metal, RE = rare earth metal; hereafter called 14:2:1) enable permanent magnets with outstanding magnetic properties. Novel chemical compositions that represent new 14:2:1 phases necessitate that they do not demagnetize at application-specific operating temperatures. Therefore, an accurate knowledge of the Curie temperature (Tc) is important. For magnetic 14:2:1 phases, we present a machine learning model that predicts Tc by using merely chemical compositional features. Hyperparameter tuning on bagging and boosting models, as well as averaging predictions from individual models using the voting regressor, enables a low mean-absolute-error of 16 K on an unseen test set. The training set and a test set have been constructed by randomly splitting, in an 80:20 ratio, of a database that contains 449 phases (270 compositionally unique) mapped with their Tc, taken from distinct publications. The model correctly identifies the relative importance of key substitutional elements that influence Tc, especially in an Fe base such as Co, Mn, and Al. This paper is expected to serve as a basis for accurate Curie temperature predictions in the sought-after 14:2:1 permanent magnet family, particularly for transition metal substitution of within 20% in an Fe or Co base.