Anna Krzyńska

Anna Krzyńska

Auto-generated profile, based on publicly available information

Anna Krzyńska

Institute of Manufacturing Technologies, Warsaw University of Technology, 02-524 Warsaw, Poland

Research Focus & Metrics

Academic Career Length

21Years (2006-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 August 2017 in Journal of Materials Processing Technology
Verified
Journal Article
Closed access
Radosław WiniczenkoRadosław Winiczenko
Radosław Winiczenko
OGOlgierd Goroch
Olgierd Goroch
AKAnna Krzyńska
Anna Krzyńska
MKMieczysław Kaczorowski
Mieczysław Kaczorowski

1 December 2012 in Archives of Foundry Engineering
Verified
Journal Article
Open access
PDF file
MKM. Kaczorowski
M. Kaczorowski
PSP. Skoczylas
P. Skoczylas
AKA. Krzyńska
A. Krzyńska
JKJ. Kaniewski
J. Kaniewski
The results of studies of W-Ni-Co-Fe experimental alloy, with chemical composition assuring a possibility of producing Ni-based supersaturated solid solution are presented. The alloy was prepared from tungsten, nickel, cobalt and iron powders which were first mixed then melted in a ceramic crucible where they slowly solidified in hydrogen atmosphere. Next specimens were cut from the casting and heated at a temperature 950°C. After solution treatment the specimens were water quenched and then aged for 20 h at a temperature 300°C. The specimens were subjected to microhardness measurements and structure investigations. The latter included both conventional metallography and SEM observations. Moreover, for some specimens X-ray diffractometry studies and TEM investigations were conducted. It was concluded that quenching lead to an increase of tungsten concentration in nickel matrix which was confirmed by Ni lattice parameter increase. Aging of supersaturated solid solution caused strengthening of the Ni-based matrix, which was proved by hardness measurements. The TEM observation did not yield explicit proofs that the precipitation process could be responsible for strengthening of the alloy

1 June 2014 in Archives of Foundry Engineering
Verified
Journal Article
Open access
PDF file
AKA. Krzyńska
A. Krzyńska
AKAndrzej Kochański
Andrzej Kochański
The results presented in this paper are a continuation of the previously published studies. The results of hest treatment of ductile iron with content 3,66%Si and 3,80% Si were produced. The experimental castings were subjected to austempering process for time 30, 60 and 90 minutes at temperature 300°C. The mechanical properties of heat treated specimens were studied using tensile testing and hardness measurement, while microstructures were evaluated with conventional metallographic observations. It was again stated that austempering of high silicone ferritic matrix ductile iron allowed producing ADI-type cast iron with mechanical properties comparable with standard ADI.

1 December 2014 in Archives of Foundry Engineering
Verified
Journal Article
Open access
PDF file
AKA. Krzyńska
A. Krzyńska
AKAndrzej Kochański
Andrzej Kochański
Austenitization is the first step of heat treatment preceding the isothermal quenching of ductile iron in austempered ductile iron (ADI) manufacturing. Usually, the starting material for the ADI production is ductile iron with more convenient pearlitic matrix. In this paper we present the results of research concerning the austenitizing of ductile iron with ferritic matrix, where all carbon dissolved in austenite must come from graphite nodules. The scope of research includedcarrying out the process of austenitization at 900° Cusing a variable times ranging from 5 to 240minutes,and then observations of the microstructure of the samples after different austenitizing times. These were supplemented with micro-hardness testing. The research showed that the process of saturating austenite with carbon is limited by the rate of dissolution of carbon from nodular graphite precipitates

1 March 2006 in Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture
Verified
Journal Article
Closed access
AKA Krzyńska
A Krzyńska
WWW Włosiński
W Włosiński
MKM Kaczorowski
M Kaczorowski
The joint copper-alumina obtained at a solidification condition of Cu/Cu2O eutectic was studied. Experiments involved many different techniques, such as scanning electron microscopy (SEM), X-ray diffractometry, X-ray microanalysis, and transmission electron microscopy (TEM). It was observed that a thin inhomogeneous interfacial layer is present between Cu and Al2O3 ceramics and it consists of two sublayers: the first is nanocrystalline complex oxide CuAlO2. This layer changes progressively into a crystalline CuAl2O4 sublayer. A model of liquid phase bonding between copper and alumina is proposed.

2 February 2022 in Materials
Verified
Journal Article
Open access
PDF file
Radosław WiniczenkoRadosław Winiczenko
Radosław Winiczenko
MKMieczysław Kaczorowski
Mieczysław Kaczorowski
AKAnna Krzyńska
Anna Krzyńska
OGOlgierd Goroch
Olgierd Goroch
ASAndrzej Tomasz Skibicki
Andrzej Tomasz Skibicki
PSPaweł Skoczylas
Paweł Skoczylas
The temperature distributions, microstructure, and mechanical properties of tungsten composite with aluminum alloy friction-welded joints are presented in this paper. The effects of welding parameters on flash diameter, shortening, joint efficiency, microhardness, and microstructure were studied. Empirical temperature models for heating and cooling phases are proposed in this study. The predicted maximum temperatures at the periphery and in the axis of aluminum specimens were close to 550 °C and 480 °C at the interface, respectively. Moreover, the peak temperature in the weld zone was studied analytically. A maximum tensile strength of 234 MPa was reached for the following welding parameters: friction time of 3.5 s and friction force of 12.5 kN. The efficiency of the welded samples decreased after reaching the maximum value, with an increase of friction time and force. Maximum hardness at the interface and the half-radius reached 100 HV and 80 HV in the aluminum alloy joints, respectively. Dynamic recrystallisation areas on the aluminum alloy side were observed. Transmission electron microscopy observations of the microstructure in the aluminum alloy revealed the presence of a high dislocation density compared to the parent material.