4 February 2020 in Superconductor Science and Technology
Of crucial importance for the application of high temperature superconducting coated conductors (CCs) is the delamination strength due to thermal stress and Lorentz force during their operation. This paper reports the mechanical delamination strengths of YBCO CCs at room temperature and 77 K, as well as the electro-mechanical delamination strength form a modified anvil tensile method. Compared to previous measurement setups, our anvil device only has one degree of freedom of transverse tension. Moreover, we use a vertical soldering technique to ensure the data reliability. Since we eliminate the influence of the measurement method on the experimental results, a naturally discrete property of the delamination strength is obtained. To describe these experimental data, a three-parameter Weibull distribution function has been suggested and a new criterion for determining delamination strength is proposed from the reliability function, which can be conveniently referred to for engineering design.
25 May 2021 in Nature Communications
The second generation HTS wires have been used in many superconducting components of electrical engineering after they were fabricated. New challenge what we face to is how the damages occur in such wires with multi-layer structure under both mechanical and extreme environment, which also dominates their quality. In this work, a macroscale technique combined a real-time magneto-optical imaging with a cryogenic uniaxial-tensile loading system was established to investigate the damage behavior accompanied with magnetic flux evolution. Under a low speed of tensile strain, it was found that the local magnetic flux moves gradually to form intermittent multi-stack spindle penetrations, which corresponds to the cracks initiated from substrate and extend along both tape thickness and width directions, where the amorphous phases at the tip of cracks were also observed. The obtained results reveal the mechanism of damage formation and provide a potential orientation for improving mechanical quality of these wires.
13 February 2020 in Physical Review Applied
Flux avalanche is commonly found in type II superconductors, and this event is always featured as being unpredictable and having ultrafast development with time. It is difficult to capture dynamically by any experimental method available today. Here, we propose a hypervelocity magnetic-optical system with two optical branches; one branch can trigger a dendritic flux avalanche in a superconducting film, and the other is capable of producing continuous multiexposure to record the lightning avalanche process. In contrast with some traditional trigger models, the present method realizes control of the position where the flux avalanche takes place. Second, we study the sensitive dependence on initial conditions of the present flux avalanche and find a series of positive Lyapunov exponents between two adjacent trajectories, which can be considered direct evidence for the chaotic dynamics in this kind of avalanche. Moreover, we reveal that, whether the laser spot is in the Meissner state or the mixed state, avalanches always penetrate from the edge of the superconducting film to the Meissner region, instead of occurring around the laser spot. This behavior clearly demonstrates that the presented avalanche is driven by the magnetic pressure force, which suggests that the optically triggered vortex avalanche possesses a different mechanism from that of the thermomagnetic avalanches commonly found in superconducting films.
1 February 2014 in Review of Scientific Instruments
We construct an instrument to study the behavior of the critical current in superconducting tapes as a function of magnetic field and axial tension strain. The apparatus combines a material testing machine made by the non-magnetic stainless steel, which is capable of producing mechanical forces up to 1000 N and magnetic field up to 5 T with a homogeneous range of Φ150 × 110 mm. Moreover, the apparatus allows the automatic measurement of time dependence of voltage (V-t) under different magnetic fields and applied strains, which can be used to investigate the vortex instability and its time effect in the superconducting tapes. As an example, the simultaneous measurements of critical current and voltage relaxation with time at various strains and magnetic fields for the YaBa2Cu3O7−x coated conductors are carried out. Comparisons are made with the earlier reports in literature; the strain and magnetic field dependence of critical current indicate consistent behavior of this instrument.
27 August 2020 in Superconductor Science and Technology
Cracks caused by tensile stress in YBa 2 Cu 3 O 7-x -coated conductors (YBCO-CCs) can cause irreversible degradation to their superconducting properties. Understanding the initiation and propagation modes of cracks can assist in preventing conductor failure and enhancing their mechanical properties in further. In this study, we used a chemical etching method and scanning electron microscopy to investigate crack morphology in the YBCO layer of conductors where the protective metal layer had been removed. For YBCO-CCs that experienced no deformation, many non-superconducting phase particles were observed and their grain size distribution corresponded to a Gaussian distribution. Energy dispersive x-ray spectroscopy identified these as Y-Cu-O particles. For the YBCO-CCs that experienced axial tension at 77 K, different propagation modes of cracks in the YBCO layer, including transgranular fracture, branching, deflection and pinning were observed for the first time. Statistical analysis demonstrated that transgranular fracture occurred in ∼ 95% of the crack modes. We analysed the reason for this phenomenon considering the thermal stresses stored inside and around the non-superconducting phase particles. The coefficient of thermal expansion of the Y 2 Cu 2 O 5 particles is less than that of the YBCO superconducting matrix, and therefore, the hoop tensile stress generated near the boundary of the Y 2 Cu 2 O 5 particle accelerates the bottom-up propagation of the crack. The other crack propagation modes such as crack branching, deflection, pinning and bridging in the YBCO layer can be considered mechanisms of blocking crack propagation that can increase the fracture toughness of the YBCO layer.
1 July 2016 in Review of Scientific Instruments
We construct a visible instrument to study the mechanical-electro behaviors of high temperature superconducting tape as a function of magnetic field, strain, and temperature. This apparatus is directly cooled by a commercial Gifford-McMahon cryocooler. The minimum temperature of sample can be 8.75 K. A proportion integration differentiation temperature control is used, which is capable of producing continuous variation of specimen temperature from 8.75 K to 300 K with an optional temperature sweep rate. We use an external loading device to stretch the superconducting tape quasi-statically with the maximum tension strain of 20%. A superconducting magnet manufactured by the NbTi strand is applied to provide magnetic field up to 5 T with a homogeneous range of 110 mm. The maximum fluctuation of the magnetic field is less than 1%. We design a kind of superconducting lead composed of YBa2Cu3O7-x coated conductor and beryllium copper alloy (BeCu) to transfer DC to the superconducting sample with the maximum value of 600 A. Most notably, this apparatus allows in situ observation of the electromagnetic property of superconducting tape using the classical magnetic-optical imaging.