4 October 2018 in ACS Nano
11 December 2017 in IEEE Electron Device Letters
as continued scaling of silicon FETs grows increasingly challenging, alternative paths for improving digital system energy efficiency are being pursued. These paths include replacing the transistor channel with emerging nanomaterials (such as carbon nanotubes), as well as utilizing negative capacitance effects in ferroelectric materials in the FET gate stack, e.g., to improve sub-threshold slope beyond the 60 mV/decade limit. However, which path provides the largest energy efficiency benefits – and whether these multiple paths can be combined to achieve additional energy efficiency benefits – is still unclear. Here, we experimentally demonstrate the first negative capacitance carbon nanotube FETs (CNFETs), combining the benefits of both carbon nanotube channels and negative capacitance effects. We demonstrate negative-capacitance CNFETs, achieving sub-60 mV/decade sub-threshold swing with an average slope of 55 mV/decade at room temperature. The average on-current (ION) of these negative capacitance FETs improves by 2.1 × vs. baseline carbon nanotube FETs (i.e., without negative capacitance) for the same off-current (IOFF). This work demonstrates a promising path forwards for future generations of energy-efficient electronic systems.
27 December 2018 in IEEE Transactions on Nanotechnology
Carbon nanotube FETs (CNFETs) promise significant energy efficiency benefits versus silicon for digital systems. While these projected benefits are for CNFETs with similar geometries as silicon FETs (e.g., top-gate FETs, with the FET gate on top of the channel), the majority of the demonstrated CNFETs leverage back-gate geometries due to ease of fabrication (i.e., the gate is fabricated before and underneath the FET channel). Although back-gate CNFETs have already been experimentally demonstrated, importantly, there lacks any rigorous analysis of their benefits for digital very-large-scale integrated (VLSI) circuits. Here, we rigorously quantify, for the first time, the benefits of back-gate geometries: both for enabling aggressive device scaling as well as VLSI circuit energy-delay product (EDP) benefits. The key contributions of this paper are: 1) first analysis of back-gate FET geometries for digital VLSI circuits, showing they enable >1.6× additional EDP benefit for CNFETs due to reduced parasitic capacitances (versus top-gate CNFETs), 2) our analysis shows that leveraging back-gate FETs enables aggressive FET scaling to sub-3-nm technology nodes, and 3) as a feasibility case study, we experimentally realize digital logic circuits that fit within the world's smallest contacted gate pitch to date (CGP, a key metric defining the area of an FET and consequently the technology node) of 30 nm.
5 August 2019 in Applied Physics Letters
As continued silicon scaling is becoming increasingly challenging, emerging nanotechnologies such as carbon nanotubes (CNTs) are being explored. However, experimental measurements of CNT Field-Effect Transistors (CNFETs) often exhibit substantial off-state leakage current (IOFF), resulting in increased leakage power and potential incorrect logic functionality. In this work, we (1) provide insight into a key component of this off-state leakage current and experimentally demonstrate that it stems from gate-induced drain leakage commonly referred to as GIDL, (2) provide an experimentally calibrated model that closely matches our measured results, and (3) demonstrate a path for mitigating GIDL current by engineering CNFET geometries with asymmetric gates: local back-gate CNFETs whose gate overlaps the source but not the drain. We demonstrate experimentally that this approach can reduce off-state leakage current by >60× at the same bias voltage (implemented across a wide range of scaled CNFETs with gate lengths ranging from >2 μm to 180 nm). This reduced leakage current due to the asymmetric gates translates to additional energy-efficiency benefits for CNFETs. Thus, this work addresses a key challenge facing CNFET-based electronics (while simultaneously providing additional energy-efficiency benefits) and is applicable to a wide-range of emerging one-dimensional and two-dimensional nanomaterials.
2 July 2025 in Physical Review Applied
31 March 2022 in Advanced Electronic Materials
Carbon nanotubes (CNTs) are a rapidly maturing emerging technology for next‐generation energy‐efficient digital Very‐Large‐Scale‐Integrated (VLSI) systems. However, a major remaining challenge facing CNT field‐effect transistors (CNFETs) are metallic CNTs, causing incorrect logic functionality and increased leakage power. As no CNT synthesis technique demonstrates a reliable path toward manufacturing 99.99% semiconducting CNTs (s‐CNT; required purity for VLSI systems), significant work focuses on solution‐based sorting of CNTs (selectively removing metallic CNTs post‐synthesis). Yet, there lacks both well‐controlled comparisons carefully optimizing key processing parameters simultaneously (CNT synthesis sources, polymer additive used for selective sorting, etc.), as well as statistically significant electrical transistor characterization sample sizes to form concrete conclusions. Here, >90 000 CNFETs (totaling >90 million CNTs) are fabricated and characterized to demonstrate the following key advances: 1) systematic exploration of the impact of different combinations of CNT synthesis sources and polymer additives on the electrical performance of transistors (analyzing on‐current, off‐current, on off ratio, and threshold voltage) to find the best combination, 2) how the optimization and choice of the CNT source can be decoupled from that of the polymer, and 3) an optimal CNT solution that achieves >99.99% s‐CNT purity using electrical measurements, meeting the requirement for VLSI systems.