This paper presents a 3D-printed hemispherical lens integrated with a planar ultra-wideband (UWB) antenna. The flower-shaped stub slot UWB antenna is made of 0.8-mm FR-4. The operating frequency of the UWB covers 3.10 GHz - 11.6 GHz with a nominal gain at zero degrees of 1.74 dBi. To enhance the UWB antenna’s high-gain radiation, a 3D-printed additive hemispherical lens is designed and fabricated from acrylonitrile butadiene styrene (ABS). The electrical properties, i.e., relative permittivity and loss tangent, of ABS are 2.66, and 0.003, respectively. Four different lens radii (8 mm, 10 mm, 12 mm, and 14 mm) are chosen to investigate the gain of the antenna. In all four cases, the 3D-printed lens is fixed in place in front of the UWB antenna with an optimum gap of 3 mm chosen to reduce the wave reflection between the lens and source antenna. Based on the measurement results, the reflection coefficient, S11, of four conditions still covers the UWB frequency range. The nominal gain at zero-degree values for lens radii of 8 mm, 10 mm, 12 mm, and 14 mm are 3.43 dBi, 4.22 dBi, 4.73 dBi, and 5.18 dBi, respectively. The proposed additive 3D-printed dielectric lens antenna also offers many advantages, i.e., ease of design and assembly, low-cost fabrication, and size reduction for high-gain antennas. Furthermore, the high-gain antenna provides a narrow half power beamwidth, which can be implemented to increase the resolution of the imaging system.
23 March 2024 in International Journal of RF and Microwave Computer-Aided Engineering
This paper presents a low-profile dual-band microstrip patch antenna operated at the 2.45/5.8 GHz ISM bands, targeting wireless body area network (WBAN) applications. The proposed antenna is fabricated on a jean substrate measuring mm2. The four corners of the conventional rectangular patch are cut to activate an additional operating frequency and to enhance the radiation pattern. The circular slot is added to the radiating patch to fine-tune the desired frequencies. The measured impedance bandwidth of the proposed antenna at 2.45 GHz and 5.8 GHz bands is 3.68% (2.40 GHz–2.49 GHz) and 3.81% (5.67 GHz–5.89 GHz), respectively. The measured maximum gains are 3.08 dBi at 2.45 GHz and 2.15 dBi at 5.8 GHz. Moreover, the antenna’s performance when placed on flat and rounded body surfaces is also investigated. The proposed antenna achieves stable radiation pattern and low specific absorption rate (SAR) value with low complexity in design. The results indicate that the proposed antenna can be a promising candidate for WBAN applications.
In this paper, the tapered slot antenna (TSA) with corrugation is proposed for UWB applications. The multi-section binomial transformer is used to design taper profile of the proposed TSA that does not involve using time consuming optimization. A step-by-step procedure for synthesis of the step impedance values related with step slot widths of taper profile is presented. The smooth taper can be achieved by fitting the smoothing curve to the entire step slot. The design of TSA based on this method yields results with a quite flat gain and wide impedance bandwidth covering UWB spectrum from 3.1 GHz to 10.6 GHz. To further improve the radiation characteristics, the corrugation is added on the both edges of the proposed TSA. The effects of different corrugation shapes on the improvement of antenna gain and front-to-back ratio (F-to-B ratio) are investigated. To demonstrate the validity of the design, the prototypes of TSA without and with corrugation are fabricated and measured. The results show good agreement between simulation and measurement.
11 July 2025 in EURASIP Journal on Wireless Communications and Networking
This paper presents a low-profile ultra-wideband (UWB) antenna with artificial magnetic conductor (AMC), designed wireless body area network (WBAN) applications. The use of all- textile materials both substrate and conductive elements in antenna design offers advantages such as low profile, flexibility, and lightweight construction. The prototype of proposed monopole antenna is fabricated on felt substrate with dimensions of 35 $$\times$$ 40 mm2. The designed antenna achieves a wide bandwidth ranging from 3.01 to 13 GHz. Furthermore, the AMC reflector with dimensions of 79 $$\times$$ 79 mm2 is placed behind the antenna. The integration of an AMC reflector effectively reduces SAR and improves performance in proximity to the human body. The simulated SAR value of proposed antenna without AMC reflector is reduced from 22.9 to 0.292 W/kg when the AMC reflector is positioned beneath it. This SAR value is below the safety limit of 2 W/kg for a 10 g mass of tissue. Moreover, the designed antenna with AMC reflector achieves a maximum gain of 9.67 dBi at 11 GHz. The results indicate that the proposed antenna is suitability for WBAN applications due to its wideband operation, low profile, flexibility, and low SAR.
This paper presents the design and analysis of antipodal Vivaldi antennas (AVAs) for breast cancer detection. In order to enhance the antenna gain, different techniques such as using the uniform and non-uniform corrugation, expanding the dielectric substrate and adding the parasitic patch are applied to original AVA. The design procedure of two developed AVA structures i.e., AVA with non-uniform corrugation and AVA with parasitic patch are presented. The proposed AVAs are designed on inexpensive FR4 substrate. The AVA with non-uniform corrugation has compact dimension of mm2 or , where is wavelength of the lowest operating frequency. The antenna can operate within the frequency range from 1.63 GHz to over 8 GHz. For the AVA with parasitic patch and uniform corrugation, the overall size of antenna is mm2 or It can operate within the frequency range from 1.4 GHz to over 8 GHz. The maximum gain for AVA with non-uniform corrugation and AVA with parasitic patch and uniform corrugation are 9.03 and 11.31 dBi, respectively. The corrugation profile and parasitic patch of the proposed antenna are optimized to achieve the desired properties for breast cancer detection. In addition, the proposed AVAs are measured with breast phantom to detect cancerous cell inside the breast and the performance in detecting cancerous cell are discussed. The measured result can confirm that the proposed AVAs can detect unwanted cell inside the breast while maintaining the compact size, simple structure and low complexity in design.
The ultra-wideband antipodal Vivaldi antenna with non-uniform corrugation for breast cancer detection is proposed in this paper. The proposed antenna is designed on a low cost FR4 substrate with the overall size of 50 x 50 mm 2 . To further enhance directivity of the antenna, the cosine-shaped corrugation is added on both outer edges of the original antipodal Vivaldi antenna. By choosing the appropriate slot length of corrugation, the reflection coefficient and antenna gain can be improved. The effects of uniform and non-uniform corrugation on reflection coefficient and gain are studied. The proposed antenna can operate in the frequency of 1.63 to over 12 GHz. Compared to the original antipodal Vivaldi antenna without corrugation, the designed antenna with non-uniform corrugation achieves maximum gain of 9.34 dBi without changing the overall size of antenna.