15 October 2025 in Earth and Planetary Science Letters
25 October 2023 in Earth and Planetary Science Letters
27 December 2023 in Geophysical Research Letters
Pore fluids are ubiquitous throughout the lithosphere and are commonly invoked as the cause of induced seismicity and slow earthquakes. We perform lab experiments to address these questions for drained fault conditions and low pore pressure. We shear simulated faults at effective normal stress of 20 MPa and pore pressures Pp from 1 to 4 MPa. We document the full range of lab earthquake behaviors from slow slip to elasto‐dynamic rupture and show that slow slip can be explained by the slip rate dependence of the critical rheologic stiffness without dilatancy hardening or other fluid effects. Our fault permeabilities ranges from 10−18 to 10−17 m2 with an initial porosity of 0.1 and estimated fluid diffusion time ≈1 s. Slow slip and quasi‐dynamic fault motion may arise from high Pp at higher pressures but dilatancy strengthening is not a general requirement.
28 July 2025 in Journal of Geophysical Research: Solid Earth
The dynamics of fluid flow within faults plays a critical role in the evolution of fault strength through the seismic cycle. The key processes that control how fluids affect fault slip behavior are the evolution of fault porosity and fluid recharge and drainage during slip that, in turn, determine dilational strengthening or compaction weakening. Despite the significance of these processes, high‐fidelity lab measurements that include the evolution of porosity, fluid pressure and frictional properties are sparse. Here, we report such data for drained and undrained velocity‐stepping experiments from 3 to 300 µ/s on natural fault gouges from the seismogenic zone of injection well 16A (2,050–2,070 m) of the Utah FORGE enhanced geothermal site site. We conducted a suite of experiments under constant normal stresses (44 MPa) and pore fluid pressures (13, 20, 27 MPa) corresponding to pore fluid factors between 0.3 and 0.65. We carefully monitor the volumetric strain and show that the dilatancy coefficient of the material ranged from 5 to , and showed minor sensitivity to fluid boundary conditions. In some cases, we see that larger slip velocities cause a transition from dilatancy strengthening to compaction weakening via fluid pressurization. Two effective fault permeability terms were required to model that fault‐fluid response with slip. We posit that the spatial‐temporal pattern of pore‐throat size and connectivity creates a spectrum of fault drainage conditions, ultimately controlling the mode of fault slip.
13 May 2026 in AGU Advances
Following an earthquake, faults lock and regain strength via a combination of healing mechanisms that include pressure solution, contact growth, and cementation. Fault healing dictates strength recovery during the seismic cycle and is therefore a key factor controlling earthquake recurrence intervals, stress drop, and other source properties. Field and laboratory studies indicate that healing derives from frictional and chemical processes acting in concert from the atomic to the fault scale. Although field studies and theoretical considerations suggest that fault healing involves thermally activated and chemically assisted processes, few laboratory studies have directly examined these mechanisms. Here, we investigate fault‐healing mechanisms via experiments on anhydrite gouges under dry, saturated, and fluid‐pressurized conditions. Our results illuminate the role of both frictional and cementation processes and show that the presence of fluids significantly enhances fault healing in anhydrite gouge, ultimately promoting a time‐dependent increase in fault cohesive strength. The increase in fault strength observed in the presence of fluids is driven by the hydration reaction of anhydrite. We propose a coupled frictional–chemical healing model that accounts for both the stress dependence and chemical kinetics of hydration at frictional contacts. We incorporate cohesion into the rate‐and‐state friction (RSF) stability criterion (Kc) and show that it provides a mechanism for earthquake nucleation that operates even in velocity‐strengthening lithologies, with broad implications for the seismogenic potential of fault zones.
21 June 2024 in Journal of Geophysical Research: Solid Earth
The frictional velocity dependence and healing behavior of subduction fault zones play key roles in the nucleation of stick‐slip instabilities at convergent margins. Diagenetic to low‐grade metamorphic processes such as pressure solution are proposed to be responsible for the change in frictional properties of fault materials along plate interfaces; pressure solution also likely contributes to the acceleration of healing according to previous studies. Here, we report friction studies for temperatures of 20–100°C and normal stresses from 20 to 125 MPa on samples collected from ancient subduction fault zones, the Lower Mugi and Makimine mélanges of the Cretaceous Shimanto belt. The two mélanges correspond to the updip and downdip limits of the seismogenic zone and include deformation features that indicate lower and higher degrees of pressure solution. Our data show that the Lower Mugi mélange exhibits velocity‐weakening to velocity‐neutral frictional behavior under low normal stress and that the Makimine mélange sample shows velocity‐strengthening behavior under high normal stress. We suggest that mineralogical changes due to diagenesis and metamorphism influence fault slip behavior. We measure frictional healing in slide‐hold‐slide experiments for the Lower Mugi mélange sample and document the role of pressure solution in fault healing. Our results show that frictional healing increases at higher temperatures. The microstructures related to pressure solution found in the post‐experimental gouges support the idea that the enhanced healing is related to pressure solution.