20 July 2022 in Journal of Microelectromechanical Systems
We demonstrate the transmission of ultrasound in air using a device that resembles a MEMS microphone in its construction. The device has a 1 mm diameter diaphragm and uses a perforated backplate for electrostatic actuation. The device is driven with large amplitude AC signals, with peak values that exceed the pull-in voltage of the diaphragm. In doing so, relatively large diaphragm displacements are achieved, as the diaphragm oscillations traverse the complete diaphragm-backplate gap. Large amplitude diaphragm vibration is advantageous for high SPL applications in air, as sound pressure is directly proportional to diaphragm displacement for a given operating frequency. Transient diaphragm displacement waveforms are measured in response to tone-burst waveforms ranging in frequency from 4 kHz to 97 kHz. Resultant acoustic pressure waveforms in air are made using a broadband microphone. 2022-0082
3 February 2025 in IEEE Sensors Journal
Silicon photonics has emerged as a popular platform for building sensors that can perform a wide range of measurements with high sensitivity. Here an optical accelerometer in silicon photonics platform was designed, and a fabricated device’s performance was characterized using integrated thermal electric modulators and shaker tests. The device operation is based on the balanced Mach-Zehnder interferometer (MZI) that resides in the top layers of a silicon chip. The chip is packaged to form a cantilever beam. As the chip undergoes acceleration, the reference arm of an MZI maintains stationary phase while the sensing arm bends. Multiple loops of serpentine waveguides were used to increase sensitivity. When light from the reference and sensing arms are combined, the output light has an intensity that is modulated by the imparted acceleration. These intensity variations are detected by a fiber coupled photodetector. An analytical model is presented combining optical and mechanical subsystems and is used to identify small designs with sub 10ng/√Hz noise floor. The sensor can transmit analog sensor data over long distances via the attached fiber array, making the sensor attractive for deep subsurface seismic measurements running several kms underground at elevated temperatures.
3 April 2025 in IEEE Sensors Journal
A bimorph lithium niobate (LiNbO3, LN) transducer has been proposed as a microphone. Surface electrodes sense the lateral in-plane electric field in thin LN films resulting from out-of-plane deformation due to acoustic pressure. The bimorph is implemented using LN films with opposing polarization, achieved with a wafer bonding approach. The article summarizes our work on an LN microphone using an LN diaphragm with $300~\mu $ m thickness and a quarter-inch diameter. Laser Doppler vibrometer (LDV) measurements are performed using piezoelectric excitation of the diaphragm to characterize mode shapes of the diaphragm. Pitch-catch acoustic measurements are performed in the air using tone burst waveforms. We characterized acoustic sensitivity and noise floor. Lumped element and finite element analysis (FEA) are used to predict the acoustical performance. This is the first work demonstrating LN material in microphone applications. We ultimately envision using a bimorph LN film with $2~\mu $ m thickness in total on the silicon substrate, where an approximately $1\times 1$ mm diaphragm is formed via a backside through wafer etch. A rigorous lumped element model is used to simulate the LN microelectromechanical systems (MEMS) microphone with a 73.58-dB signal-to-noise ratio (SNR). Improving MEMS microphone SNR beyond the current state-of-the-art is challenging. LN microphones may be a viable path.
1 May 2023 in The Journal of the Acoustical Society of America
The majority of reported measurements on high intensity ultrasound beams in air are below 40 kHz and performed on standing waves inside of a guide. Here, experimental characterization of high intensity progressive and divergent sound beams in air at 300 kHz are presented. Measurements in this frequency range are challenging. Accurate characterization of high intensity sound beams requires a measurement bandwidth at least ten times the beam's primary frequency, as high intensity soundwaves steepen and form shocks and, therefore, contain significant signal power at harmonic frequencies. Hence, a measurement bandwidth of at least 3 MHz is required. Calibrated measurement microphones are generally not available in this frequency range. This limitation has been overcome by using a hydrophone with a calibrated response from 250 kHz to 20 MHz. A narrowband piezoelectric transducer is used as the source in this study, and it is capable of generating tone burst waveforms centered at 300 kHz with 160 dB sound pressure level surface pressure. Cumulative wave steepening and shock formation are observed in on-axis measurements. The source's surface vibration profile is measured using a scanning laser Doppler vibrometer, and the vibration profile is imported into a numerical wide-angle Khokhlov-Zabolotskaya-Kuznetsov simulation for comparison against measured on-axis waveforms.
24 June 2025 in IEEE Sensors Journal
Integrated photonics has emerged as a popular platform for performing a wide range of measurements with high sensitivity. Here an optical accelerometer in silicon nitride photonics platform was designed, and the fabricated device’s performance was measured. Light is first split into a reference and sensing arm. The sensing arm is a waveguide loop on top of a cantilever beam. When the cantilever is subjected to acceleration, a strain field is generated within the sensing arm that leads to a proportional optical phase change. Light passing through a reference arm is frequency shifted using an acousto-optic modulator. Light from the sensing arm, which undergoes phase modulation due to cantilever vibrations, is combined with the frequency-shifted light from the reference arm. After passing the combined beams through a photodiode, demodulation of the voltage waveform into the in phase and quadrature signals enables the phase from the sensing arm to be measured over many optical fringes. This approach extends the intrinsic dynamic range (IDR) of the optical interferometric readout beyond the limits of conventional interferometric sensors with an improved dynamic range of more than 40dB compared with conventional method with no active feedback. A calculated MDS of 190ng/√Hz was achieved while a further improvement was discussed. The prototype devices are fabricated using low loss silicon nitride photonics platform, all on an SOI wafer with Si device layer. The process enables two post-optical-waveguide fabrication processes; front side and backside deep silicon etch (DSE). The buried oxide of the SOI serves as a controlled etch stop for both top and backside silicon etch processes. We use this process to form thin and flexible cantilevers comprising only 50 μm thick silicon.
14 May 2025 in IEEE Sensors Journal
The remarkable directional hearing capabilities of the fly Ormia ochracea have inspired advancements in acoustic sensing technologies. Despite the small size of the fly’s ear relative to the wavelength of audible sound, it can precisely locate crickets by detecting their chirps. This article presents the design, fabrication, testing, andmodeling of a biologically inspired MEMS microphone that leverages the fly’s unique hearing mechanism. The device consists of a two-sided cantilever beam that rotates about torsional pivots, producing two primary vibration modes: (1) a rocking mode, which responds to pressure gradients with out-of-phase motion for sound localization, and (2) a bending mode, which reacts to omnidirectional sound pressure with in-phase motion. The microphone is fabricated using a silicon-on-insulator wafer with a 2-μm-thick device layer and incorporates a 500-nm-thick aluminum nitride piezoelectric film for transduction. Multipoint scans validate the sensing modes, which are accurately modeled using finite element analysis. Signal readout is achieved through an integrated circuit amplifier with high bias resistance. Acoustic measurements in air are performed across audible and ultrasonic frequencies, with sensitivity results compared to simulations. The initial prototypes demonstrate optimal performance at ultrasonic frequencies near 20 kHz. Simulations further explore potential designs for broadband applications spanning the audio frequency range of 20 Hz to 20 kHz.