Background: Continuous glucose monitoring for patients with diabetes is of paramount importance to avoid severe health conditions resulting from hypoglycemia or hyperglycemia. Most available methods require an invasive setup and a health care professional. Handheld devices available on the market also require finger pricking for every measurement and do not provide continuous monitoring. Hence, continuous glucose monitoring from human tears using a glucose sensor embedded in a contact lens has been considered as a suitable option. However, the glucose concentration in human tears is very low in comparison with the blood glucose level (1/10–1/40 concentration). We propose a sensor that solves the sensitivity problem in a new way, is flexible, and is constructed onto the oxygen permeable contact lens material. Methods: To achieve such sensitivity while maintaining a small sensor footprint suitable for placement in a contact lens, we increased the active electrode area by using three-dimensional (3-D) electrode micropatterning. Fully flexible 3-D electrodes were realized utilizing ordered arrays of pillars with different shapes and heights. Results: We successfully fabricated square and cylindrical pillars with different height (50, 100, and 200 μm) and uniform metal coverage to realize sensor electrodes. The increased surface area produces high amperometric current that increases sensor sensitivity up to 300% using 200 μ tall square pillars. The sensitivity improvement closely follows the improvement in the surface area of the electrode. Conclusions: The proposed flexible glucose sensors with 3-D microstructure electrodes are more sensitive to lower glucose concentrations and generate higher current signal than conventional glucose sensors.
In this work, we present a novel design for an organic light-emitting system integrated with a mechanical energy harvesting and energy storage polymer films (patent pending). The system is configured into multiple stacked layers to form a thin, flexible, and lightweight assembly. The thin “film-like” device can be deformed and flexed to generate energy up to 0.5 mW within 100 s with ease. This platform technology finds applications in energy harvesting displays, electronic papers, key-input-pads, novel packaging, smart-IDs, disposable lab-on-a-chip optomicrofluidic systems, and much more. Results on the energy storage characteristics of the ionic polymer-metal composite film, the performance of a polyfluorene-based organic light-emitting device, and the mechanical energy transduction of the piezoelectric polymer energy harvester are presented. The polymeric nature of this platform system further makes it suitable for roll-to-roll print manufacturing, supporting applications requiring high volume and low cost.
A simple current-sourced adaptive corrosion protection system (ACPS) along with a technology to extract the protection current from the Tafel plot is presented. For reliable protection of the target metal, first, the Tafel plot of the target metal is obtained. Subsequently, a novel technique proposed in this paper is used to extract the protection current from the Tafel plot. This extracted protection current is fed to the target metal to protect the metal in the existing corrosive environment. This three-part system is adaptively used to update the required protection current to effectively protect the target metal continuously. All these functionalities are integrated in a stand-alone ACPS that effectively diagnoses the corrosion status and updates the protection parameters without any manual interaction or physical modification of the set-up to offer modularity, reliability, and cost saving. To validate the technique, a laboratory scale system is realized and tested using various metal samples and various corrosive mediums. Using the experimental system, A36 metal coupons are effectively protected with protection (inhibition) efficiency of 40–100in different corrosive mediums that can extend the life expectancy of the target metal from ~2 times to more than 100 times for the tested corrosive mediums.
In this article, we present an electro-enzymatic glucose sensor fabricated using a novel self-aligned and hybrid polymer fabrication process. The self-aligned fabrication process was carried out using polydimethylsiloxane (PDMS) as a process substrate material, SU-8 (a negative, epoxy based photoresist) as a sensor substrate material and gold as an electrode material. The electro-enzymatic glucose sensor was assembled from microfabricated components using a self-registration step. The sensor substrate is optically transparent and flexible. Utilizing the process, a wide range of bio-sensors for different constituents (e.g. lactate, pO 2 etc.) can be fabricated. The glucose sensor was successfully fabricated using our new multilayer SU-8 process on PDMS substrate. The sensor thickness was measured between 117.15 μm and 140.15 μm. The current response of the multi-layer electroenzymatic sensor using different glucose concentrations is also measured. Besides, the current response for long term stability is also presented.
1 January 2017 in Additional Conferences (Device Packaging, Hitec, Hiten, & Cicmt)
Article Citation: Hao Jiang, Jasbir N. Patel, and Bozena Kaminska (2017) Plasmon Rulers for 3D IC Alignment. Additional Conferences (Device Packaging, HiTEC, HiTEN, & CICMT): January 2017, Vol. 2017, No. DPC, pp. 1-20. https://doi.org/10.4071/2017DPC-THA1_Presentation1