Mehdi Asheghi

Mehdi Asheghi

Auto-generated profile, based on publicly available information

Mehdi Asheghi

Department of Mechanical Engineering Stanford University Stanford CA 94305 USA

Research Focus & Metrics

Academic Career Length

22Years (2005-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
18 June 2024 in Advanced Functional Materials
Verified
Journal Article
Closed access
SVSam Vaziri
Sam Vaziri
CPChristopher Perez
Christopher Perez
IDIsha M. Datye
Isha M. Datye
HKHeungdong Kwon
Heungdong Kwon
CHChen‐Feng Hsu
Chen‐Feng Hsu
XBXinyu Bao
Xinyu Bao

1 May 2014
Verified
Conference Paper
Closed access
JCJungwan Cho
Jungwan Cho
KCKenneth K. Chu
Kenneth K. Chu
PCPane C. Chao
Pane C. Chao
CMCraig McGray
Craig McGray
MAMehdi Asheghi
Mehdi Asheghi
KGKenneth E. Goodson
Kenneth E. Goodson
Self-heating effects severely limit the performance of high-power gallium nitride (GaN) high-electron-mobility transistors (HEMTs). High thermal resistances within micrometers of the transistor junction often dominate the junction temperature rise and fundamentally restrict the device power handling capability. The use of high-thermal-conductivity diamond near the junction can address this thermal limitation, but this approach requires careful attention to the quality of the thermal interface between the GaN and diamond. Here we use time-domain thermoreflectance (TDTR) to measure thermal resistances of thin silicon nitride (SiN) films with varying thicknesses on both diamond and GaN. Measurement of these two sets of samples provides an estimate for the thermal resistance between the GaN and diamond since the SiN film can be used as a bonding layer between the two materials. The effective resistances of the SiN film and bottom interface (SiN/diamond or SiN/GaN) range from 22 to 37 m2 K GW-1 for both sets of samples. Our findings suggest the possibility of achieving 22 m2 K GW-1 as the GaN/diamond thermal interface resistance.

28 August 2022 in Advanced Functional Materials
Verified
Journal Article
Closed access
CPChristopher Perez
Christopher Perez
AJAtharv Jog
Atharv Jog
HKHeungdong Kwon
Heungdong Kwon
DGDaniel Gall
Daniel Gall
MAMehdi Asheghi
Mehdi Asheghi
KGKenneth E. Goodson
Kenneth E. Goodson

9 August 2024 in Journal of Electronic Packaging
Verified
Journal Article
Closed access
MOMostafa Olyaei
Mostafa Olyaei
SSSagar Singh
Sagar Singh
KJKaiying Jiang
Kaiying Jiang
YGYashraj Gurumukhi
Yashraj Gurumukhi
KGKenneth Goodson
Kenneth Goodson
NMNenad Miljkovic
Nenad Miljkovic
A virtual testbed simulation framework is created for the economic, reliability, and lifetime analysis of battery thermal management control strategies in electric vehicles (EVs). The system-level model is created in the MATLAB environment using the Simscape library and custom components are developed as required. A lumped parameter coupled electrothermal model with temperature and state of charge (SOC)-dependent cell parameters is adopted from the literature to characterize battery performance. Suitable cell capacity degradation models are implemented to capture the cycle aging and calendar aging of the battery. The economic benefit of extending the lithium iron phosphate (LFP) battery lifetime by optimal thermal conditioning is weighed against the corresponding energy cost of the operation allowing for the assessment and adoption of economy-conscious strategies under different conditions. Active cooling of the battery using a vapor compression system along with a preconditioning strategy is benchmarked against passive cooling by a radiator for operating cost, battery lifetime, and net cost savings. Active cooling with precooling before fast charging can maintain optimal battery temperature but requires an additional electricity cost of 170–530 $/year, compared to passive cooling. However, the added cost is more than compensated for by the increase in battery lifetime by 1.4–1.9 years leading to a net saving of 140–550 $/year.

4 December 2021 in Advanced Materials Interfaces
Verified
Journal Article
Closed access
PDF file
CPChristopher Perez
Christopher Perez
RKRobert Knepper
Robert Knepper
MMMichael P. Marquez
Michael P. Marquez
EFEric C. Forrest
Eric C. Forrest
ATAlexander S. Tappan
Alexander S. Tappan
EZElbara O. Ziade
Elbara O. Ziade

6 July 2015
Verified
Conference Paper
Closed access
PDF file
CZChi Zhang
Chi Zhang
GRGuoguang Rong
Guoguang Rong
JPJames W. Palko
James W. Palko
TDThomas J. Dusseault
Thomas J. Dusseault
MAMehdi Asheghi
Mehdi Asheghi
KGKenneth E. Goodson
Kenneth E. Goodson
Microporous metals are extensively applied in convective cooling of high heat flux systems such as electronics. Traditional fabrication approaches, such as sintering of metallic particles, however, produce materials with limited fluid transport capability. Here, we demonstrate control and enhancement of the permeability of porous copper inverse opals produced via electrodeposition around a sacrificial polymer template. Sintering of the template is used to control the fluid transport network microstructure, with permeability increasing for increasing sintering times. These electrodeposited structures achieve permeabilities greater than 1×10−12 m2 with 5 μm pores, roughly 5 times larger than those of porous sintered copper with comparable feature sizes. The high permeability and small feature sizes, with attendant high specific surface area and strong capillarity, offered by the sintered template electrodeposited copper are attractive for two phase cooling applications.