Zhiming Xiao

Zhiming Xiao

Auto-generated profile, based on publicly available information

Zhiming Xiao

College of Electronic Information and Optical Engineering, Nankai University, Tianjin, China

Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
23 August 2017 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
ZXZhiming Xiao
Zhiming Xiao
This paper presents a protection circuit architecture that helps us to reduce the chances of damages in a boost switching converter due to fault conditions of output short-to-ground or power-switch short-circuits. Those two short-circuit faults can cause the inductor current to run away and result in damages. The proposed protection circuit can detect those two fault conditions within a few microseconds and then isolate the converter from its power supply. The fault detection is implemented by sensing the voltage drop across the primary inductor in a 1:1 coupled transformer which replaces the single-winding inductor in a boost converter. If a short-circuit fault happens at either the output load or at the power switch, the secondary inductor will shoot current to turn off a pass PMOSFET, which disconnects the primary inductor from the input supply. The protection circuit was built on the top of a commercial boost converter and was verified under short-circuit faults over a wide load current range. The proposed protection structure effectively reduced the inductor current overshoot during short-circuit event at the expenses of 1.2% drop of the peak efficiency during normal operation.

26 February 2024 in IEEE Journal of Solid-State Circuits
Verified
Journal Article
Closed access
QXQiuzhen Xu
Qiuzhen Xu
GLGen Li
Gen Li
YLYanyan Liu
Yanyan Liu
FLFeng Luo
Feng Luo
ZXZhiming Xiao
Zhiming Xiao
This article presents an inverter-based multichannel low-power low-noise neural signal recording amplifier with a novel differential-like operational transconductance amplifier (OTA). The differential-like OTA consists of two asymmetric branches. The inverting branch used for multichannel inputs has more inverters in parallel than that of the noninverting branch used for reference. Two virtual rails with very low impedance are designed in the differential-like OTA to effectively reduce the noise-efficiency-factor (NEF) and crosstalk in input channels. The NEF and the effective average current per channel decreases as the number of channels increases. Furthermore, by optimizing the current ratio of the inverting and the noninverting branches of the OTA, the NEF of the proposed amplifier is minimized and approaches the NEF of an ideal inverter of $\sqrt 2/2$ as the channel counts increase to infinity. The area per channel is reduced even more significantly as the channel counts increase. The proposed amplifier architecture with 4-channel, 16-channel, and 64-channel configurations were fabricated and measured. The results show that the noise, power, and area performance were all improved by integrating more channels in parallel. For the 64-channel amplifier, the measured NEF is 0.84, the effective average current per channel is 422 nA and the area per channel is only 0.044 mm $^{2}$ .

14 August 2017 in IEEE Transactions on Industrial Electronics
Verified
Journal Article
Closed access
ZXZhiming Xiao
Zhiming Xiao
This paper presents an energy efficient Power over Ethernet interface for applications that require higher power delivery than that of IEEE 802.3af and 802.3at standards allow. The proposed architecture increases the power delivered to the powered-device by utilizing all four pairs of the CAT5 cable. Maximum power is guaranteed by a current-balancing control block which equalizes the currents in the CAT5 cable. The current-balancing control is implemented in an efficient way of regulating the pass p-type metal-oxide-semiconductor transistor in the diode bridge stage. The proposed interface also includes a hot-swapping control block that protects the devices in the power conduction path by limiting both the maximum load current and the maximum voltage ramping rate. The voltage and current-limiting functions are controlled by two separated regulation loops. To reduce the power loss, a single pass n-type metal-oxide-semiconductor transistor is inserted in the ground current path and is shared by both regulation loops. The experimental result of the assembled prototype showed balanced currents among all four pairs in the CAT5 cable. In cases of hot-plugging, the proposed prototype exhibited both well-controlled inrush current and limited voltage-ramping rate under various load capacitance conditions.

13 July 2023 in IEEE Transactions on Circuits and Systems II: Express Briefs
Verified
Journal Article
Closed access
GZGuangshu Zhao
Guangshu Zhao
ZXZhiming Xiao
Zhiming Xiao
PMPui-In Mak
Pui-In Mak
RMRui P. Martins
Rui P. Martins
MLMan-Kay Law
Man-Kay Law
This brief presents a one cycle startup relaxation oscillator (RO) suitable for resource-constrained wearable and implantable applications. For improving energy efficiency without relying on a low supply voltage, we propose a self-synchronized power gating technique to completely shut down almost all the analog building blocks except near the clock toggling moment. We further relax the system startup energy and size by introducing the ratiometric threshold-referenced technique and deadlock avoidance circuit to quickly pre-bias the internal RC network without using extra on-chip references. The proposed RO is designed and fabricated in standard 0.18-lm CMOS, with four distinct implementations at 1kHz, 10kHz, 100kHz, and 1MHz. Measurement results show that all the ROs can achieve one-cycle startup operation. The 100kHz RO, which occupies an active area of only 0.041mm2, achieves a line sensitivity of ±1.14%/V from 1.7 to 1.9V while exhibiting an energy efficiency of 2.7nW/kHz. After trimming on-chip resistors with complementary temperature coefficients (TCs), the 1MHz RO attains a measured TC of 82ppm/oC from -25 to 100oC, as well as a noise-power figure-ofmerit (FoM) of 149 dBc/Hz@100kHz.

10 February 2025 in IEEE Transactions on Circuits and Systems I: Regular Papers
Verified
Journal Article
Closed access
YLYun Li
Yun Li
JJJiarun Jiang
Jiarun Jiang
PQPengda Qu
Pengda Qu
YZYue Zhao
Yue Zhao
FLFeng Luo
Feng Luo
ZXZhiming Xiao
Zhiming Xiao
An LDO that utilizes Bipolar-Junction-Transistor (BJT) as input differential pair with base current compensation structure is proposed. The NPNs and PNPs complementary input structure is designed to suppress both the flicker and thermal noise of the LDO and ensure the rail-to-rail common mode input range. The base current compensation structure is designed to ensure the output accuracy of the LDO. Moreover, by designing the current-mode reference, the proposed LDO eliminates the thermal noise from the feedback resistor network and the amplification of the noise due to the feedback coefficient. The proposed LDO was fabricated with 180nm BCD double well process with a die area of about 2.884mm $^{\mathbf{2}}$. The measured output noise of the LDO is only $\mathbf{248nV/}\sqrt {\mathbf{Hz}} $ at 10Hz, and the integrated RMS noise is 1.44$\mu $V from 10Hz to 100kHz. The LDO supports a wide supply rail range from 2.3V to 20V and a wide output range from 0.1V to 19.7V. The measured Line and Load regulations are 0.035mV/V and 0.0008mV/mA, respectively.

26 September 2017 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
ZXZhiming Xiao
Zhiming Xiao
This paper presents a low-dropout (LDO) regulator structure that is aimed at rechargeable battery powered systems where direct sensing of the load voltage is not available. The cable connecting the regulated output to the load may create a voltage drop and cause error to the load voltage. Conventional methods address this issue by increasing the LDO output voltage to compensate the cable voltage drop. The proposed architecture extends this idea by including a calibration block that updates the required compensation voltage to track the cable resistance shift due to cable length or temperature change. The measured cable-drop error was reduced from 2.4% to ~0.1% by iterating the proposed calibration process three times. Under the condition of time-varying temperature, the measured calibration process effectively reduced the cable-drop error due to the temperature-coefficient of the cable resistance. The proposed system also includes a current management block, by which the priority is set between the load current and the battery charging current. This paper proposes two architectures, the two-cable and the three-cable structures, to implement both the cable-drop calibration and the current management functions. Other functions such as input under-voltage-lockout and output current-limiting are also included and have been verified by experiment.