19 June 2020 in Journal of Lightwave Technology
We present a novel distributed high sensitivity static strain sensing method based on differential relative phase in optical frequency domain reflectometry (OFDR). By performing two separate tests of the measurement and the reference states, distributed strain sensing can be achieved by acquiring differential relative phase between these two states, which can reduce common-mode residual nonlinear phase in OFDR greatly and favor phase unwrapping, thanks to decreasing wrapped phase change rate as a function of the length of fiber under test (FUT). In addition, an all grating optical fiber that has a stronger backscattering than that of a standard single-mode fiber is used as FUT in the presented OFDR system. In the experiment, the measurement range of static strain variation is 0 to 25 με, the sensing spatial resolution is 4.35 cm, and the minimum measurable strain variation is 0.25 με along with a total 36 m FUT. Compared with the widely-used Rayleigh backscattering spectra shift cross-correlation method using the same data, the presented method can provide a better sensing performance of measuring a minor strain variation under the same sensing spatial resolution.
23 September 2022 in Journal of Lightwave Technology
We present a long distance distributed strain sensing in optical frequency domain reflectometry (OFDR) by shape-adaptive principal component analysis Block-Matching three-dimensional filter (BM3D-SAPCA) image denoising, which uses correlated patterns and high degree redundancy of sensing data for enhancing the performance of distributed sensing by image processing for removing noise and increasing the signal-to-noise ratio (SNR) of noisy measurements. Compared with 2D image denoising methods, BM3D-SAPCA method searches similar 2D image blocks and stacks them together in 3D arrays, which takes full advantage of the high level of similitude and redundancy contained on the multidimensional information to denoise. We find that the BM3D-SAPCA method can effectively suppresses noise aggravation along with an increasing of the sensing distance. Without modifying the hardware system of OFDR, we achieve a distributed strain sensing with a 5 cm spatial resolution, a 2 μϵ strain resolution on a 200 m all grating fiber. We compare the performance of distributed strain sensing by BM3D-SAPCA with Gaussian filter, wavelet denoising (WD) and non-local mean filter (NLM) using the same data. The mean maximal strain measurement error at loaded strain areas is reduced from 2.3791 μϵ to 0.6545 μϵ by BM3D-SAPCA. These mean errors by Gaussian filter, NLM and WD are 1.1177 μϵ, 1.6668 μϵ and 1.9721 μϵ, respectively. The mean standard deviations of strain measurement in eight repeat experiments is reduced from 1.5221 μϵ to 0.3134 μϵ after noise reduction by BM3D-SAPCA, which is 79.37% lower than the raw data. The mean standard deviations after noise reduction by Gaussian filter, NLM and WD are decreased by 68.85%, 64.24% and 14.41% respectively.
21 July 2021 in IEEE Photonics Journal
In distributed shape sensing, the shape reconstruction error is more and more sensitive to the strain measuring error along with curvature radius of reconstructed shape increasing, which causes a notable challenge for large curvature radius shape reconstructing. In this paper, we demonstrate a large curvature radius shape sensing using optical frequency domain reflectometry (OFDR) in multi-core fibers. We construct a theoretical model of strain measuring error and curvature radius reconstructing errors under different curvature radius. In the experiment, by this reconstructing error model, we optimally select the measurable strain resolution and the sensing spatial resolution to realize the shape reconstruction with a large curvature radius and reconstruct two-dimensional (2D) circle shapes of curvature radii from 5 cm to 100 cm. To verify the accuracy of three-dimensional (3D) shape reconstruction, we present a 3D shape sensing validation method based on 3D printing technology. We fabricate a 3D phantom containing a groove with a variable curvature radius of 5 cm to 100 cm. The presented distributed shape sensing system realize to reconstruct this complicated 3D shape. The root-mean-square error of curvature radius between the reconstructed and designed 3D space curves is 7.2 mm and the mean Euclidean distance is 3.4 mm.
22 September 2021 in IEEE Sensors Journal
We present a graphics processing unit (GPU)-based real time distributed dynamic strain sensing in optical frequency domain reflectometry (OFDR). GPU can accelerate the data processing rate distributed sensing in OFDR because it contains many parallel processing steps. We analyze parameters and performance of tunable laser source (TLS), data acquisition card (DAQ) and GPU. We present a choice method of the thread number in a block based on the GPU streaming multiprocessor utilization efficiency. We construct several kernel functions based on process steps of strain sensing and discuss the selection of blocks number for each kernel function. In the experiment, we find that total process time by the parallel computing in GPU is enhanced about 81 times compared with the serial computing in CPU. The measurement rate of this system is up to 60 Hz for real time distributed dynamic strain sensing. We achieve a dynamic strain sensing with a peak-to-peak variation of $2.5~\mu \varepsilon $ , a vibration frequency of 20 Hz and a sensing spatial resolution of 20 cm at a sensing range of 200 m. More importantly, two strain areas simultaneously loaded with a distance interval of 20 cm can be distinguished clearly.
18 August 2022 in Journal of Lightwave Technology
Ghost peaks refer to these peaks on backscattering trace measured by a reflectometer similar to Fresnel reflection peaks appearing at the position of non-reflection events in optical fiber or optical waveguide networks testing, which will cause ambiguity in the interpretation of reflection events on backscattering trace. We present a simple and effective method to eliminate side lobe ghost peaks in optical frequency domain reflectometry (OFDR) using a Wiener deconvolution filter. An OFDR system usually contains a main interferometer that is used to measure backscattering trace of fiber umber test (FUT) and an auxiliary interferometer that is used to measure the phase of tunable laser source (TLS) to compensate tuning nonlinearity. Multi-peaks in the spectrum of TLS and reflections in the auxiliary interferometer will generate side lobes on point spread function (PSF) of OFDR system, which will cause ghost peaks on FUT trace. By performing a Wiener deconvolution filtering on the auxiliary interferometer, we can obtain the PSF of an auxiliary interferometer, which is used as a convolution kernel to perform a Wiener deconvolution filtering on FUT trace from the main interferometer. Comparing the main interferometer spatial signal before and after deconvolution filtering, the peak amplitude whose reduction higher than threshold is identified to a ghost peak and is eliminated. By this ghost peak elimination method, we can acquire a pure FUT trace by an OFDR using a low-cost distributed feedback (DFB) TLS with a 26 m test length and an mm level spatial resolution.