22 September 2021 in IEEE Sensors Journal
We present a graphics processing unit (GPU)-based real time distributed dynamic strain sensing in optical frequency domain reflectometry (OFDR). GPU can accelerate the data processing rate distributed sensing in OFDR because it contains many parallel processing steps. We analyze parameters and performance of tunable laser source (TLS), data acquisition card (DAQ) and GPU. We present a choice method of the thread number in a block based on the GPU streaming multiprocessor utilization efficiency. We construct several kernel functions based on process steps of strain sensing and discuss the selection of blocks number for each kernel function. In the experiment, we find that total process time by the parallel computing in GPU is enhanced about 81 times compared with the serial computing in CPU. The measurement rate of this system is up to 60 Hz for real time distributed dynamic strain sensing. We achieve a dynamic strain sensing with a peak-to-peak variation of $2.5~\mu \varepsilon $ , a vibration frequency of 20 Hz and a sensing spatial resolution of 20 cm at a sensing range of 200 m. More importantly, two strain areas simultaneously loaded with a distance interval of 20 cm can be distinguished clearly.
13 June 2019 in Optics Express
A fiber optical anemometer using dual Fabry-Perot sensors with sealed cavity is proposed for high-speed airflow measurement. The airflow velocity is measured based on principle of differential pressure, and temperature compensation is realized by reference F-P sensor to improve measurement accuracy and environmental adaptability. The location of dual F-P sensors in the airflow field and quadratic functional relation between differential pressure and airflow velocity are obtained by the simulation of turbulence model. F-P sensors in this experiment can be employed to measure pressure from 100kPa to 107kPa and temperature from 5°C to 50°C. The full-scale error of F-P sensors is less than 0.53% by calibration. It is demonstrated experimentally this fiber optical anemometer is qualified for measuring air velocity in the range of 7.9-81m/s with velocity error less than 0.69%. The device has the potential to measure high speed airflow in various applications.
18 August 2022 in Journal of Lightwave Technology
Ghost peaks refer to these peaks on backscattering trace measured by a reflectometer similar to Fresnel reflection peaks appearing at the position of non-reflection events in optical fiber or optical waveguide networks testing, which will cause ambiguity in the interpretation of reflection events on backscattering trace. We present a simple and effective method to eliminate side lobe ghost peaks in optical frequency domain reflectometry (OFDR) using a Wiener deconvolution filter. An OFDR system usually contains a main interferometer that is used to measure backscattering trace of fiber umber test (FUT) and an auxiliary interferometer that is used to measure the phase of tunable laser source (TLS) to compensate tuning nonlinearity. Multi-peaks in the spectrum of TLS and reflections in the auxiliary interferometer will generate side lobes on point spread function (PSF) of OFDR system, which will cause ghost peaks on FUT trace. By performing a Wiener deconvolution filtering on the auxiliary interferometer, we can obtain the PSF of an auxiliary interferometer, which is used as a convolution kernel to perform a Wiener deconvolution filtering on FUT trace from the main interferometer. Comparing the main interferometer spatial signal before and after deconvolution filtering, the peak amplitude whose reduction higher than threshold is identified to a ghost peak and is eliminated. By this ghost peak elimination method, we can acquire a pure FUT trace by an OFDR using a low-cost distributed feedback (DFB) TLS with a 26 m test length and an mm level spatial resolution.
1 April 2025 in IEEE Sensors Journal
Distributed optical fiber vibration sensor (DOFVS) is an ideal technology for integrated sensing and communication in an optical fiber (ISAC-OF), which can be widely applied to urban structure health monitoring, ocean seismic detection, and pipelines/cable/border safety monitoring. In this paper, we present a single-ended > 100 km distributed vibration sensor based on OFDR by detecting Rayleigh backscattering change that is evaluated by Pearson correlation coefficient (Pearson-CC). By simple internal modulation OFDR system without any amplifier, specialty optical fiber and complex modulation techniques, vibration event can be located by detecting changepoints in step form in Pearson-CC, and the amplitude of vibration event is proportional to the differential Pearson-CC. Pruned exact linear time (PELT) algorithm is performed in Pearson-CC along fiber under test (FUT) to detect all changepoints. In experiments, we achieve distributed vibration sensing with a range of 100.9 km, a sensing spatial resolution of 15.3 m and a strain resolution of 868 pε. The differential Pearson-CC and amplitude of vibration event have a good linear relationship, whose R-square reaches 0.9993. We also successfully locate two simultaneous vibration events over 100 km fiber.
18 July 2012 in Applied Physics Express