8 April 2022 in IEEE Transactions on Instrumentation and Measurement
Magnetic particle testing (MT) has been widely used in nondestructive testing (NDT) of ferromagnetic materials. MT can be divided into wet method and dry method. The wet method is highly sensitive for microcracks and easy to operate. But the problem is that magnetic suspension liquid utilized in the wet method pollutes both test objects and environment. Dry magnetic particles utilized in dry method are recyclable and environmentally friendly. But the irrelevant magnet particles must be manually removed to reveal the magnetic particle indication (MPI). This operation limits both the detection efficiency and sensitivity of dry method. To increase the automation in MT, this article proposes a thermography-based dry MT method (TDMT). Specifically, the dry magnetic particles are heated before utilization and then thermal data are utilized for crack identification. TDMT inherits the economic and environmental advantages of the dry method. Additionally, the time-varying thermal data can provide more useful information than conventional MPI, which makes it possible to identify cracks without manual assistance. The mathematical model of TDMT is designed to prove its feasibility and a dimensionality reduction-based algorithm is applied for crack signal enhancement. Experiments on different specimens with artificial and natural cracks have been conducted. The notch with both a depth of $15~\mu \text{m}$ on the standard test shim and a width up to 0.8 mm on the steel plate can be successfully detected. The high sensitivity and wide detection range can be seen from TDMT.
30 August 2023 in Mechanical Systems and Signal Processing
23 April 2022 in Journal of Nondestructive Evaluation
12 March 2024 in IEEE Transactions on Industrial Informatics
Surface cracks in the raceway of hub bearings pose a significant safety threat. Magnetic particle testing (MPT) can be used to locate these cracks regardless of the influences caused by raceway structure. However, crack identification and evaluation in conventional MPT are quite challenging due to the low correlation between magnetic particle indication (MPI) and inspection images. To address this problem, this article introduces a dynamical MPI measuring method through 3-D vision. Specifically, a scanning 3-D vision system, an approach to forming MPI, and a curvature feature–based algorithm for MPI identification are newly proposed. 3-D measurement directly captures the spatial aggregation state of the magnetic particles, thereby enabling the connection between MPI and the cause of it, which is the leakage magnetic field above cracks. Starting from the electromagnetic field, we analyze the potential features of the 3-D profile of MPI. Magnetic force serves as a link, providing a theoretical basis for the identification and evaluation. Experiments show that our method successfully detects artificial notches with depths of 0.5–2.5 mm and natural microcracks with a maximum width of 40 μ m and differentiates between variations in crack depths of 0.5 mm. The sensitivity, stability, and evaluation ability can be demonstrated.
24 December 2021 in IEEE Transactions on Instrumentation and Measurement
In oil mining system, stress cracks on thread usually lead to drill pipe failure. To maintain normal operation of drill pipes, the thread needs to be nondestructively tested. However, due to complicated structure, it is challenging to identify and quantify the cracks the using existing nondestructive testing (NDT) methods. In this article, a scanning induction thermography (SIT) system for automatic detection of drill pipe thread (DPT) is presented. Specifically, a profiling heating method (PHM) is proposed to produce uniform heating on the root part of thread tooth where most of the stress cracks occur. A weighted least squares fitting (WLSF)-based difference algorithm is used to eliminate the background temperature of scanning data. The algorithm can extract crack thermal response with the influence of lift-off distance change and marginal effect of electric field in SIT. Experiments show that the proposed system can obtain 3k thermal contrast between crack and defective-free area when testing the crack with only 0.3 mm depth. Three SIT systems with other heating methods are also used for comparison. Better heating uniformity, signal intensity, robustness of structural change, linear property with depth information, and signal consistency when testing similar cracks in different areas of the root part can be demonstrated in the proposed system.
13 March 2024 in IEEE Transactions on Instrumentation and Measurement
Magnetic particle testing (MT) has the advantages of high sensitivity and adaptability. However, during the formation of magnetic particle indication (MPI) corresponding to surface opening defects, the defects are filled with magnetic particles, resulting in the weakening of the leakage magnetic field (LMF), a phenomenon that has been ignored in existing studies. In order to enhance the visual feature of MPI, this paper proposes an isolation strip-based magnetic particle testing method (ISMT), which can avoid the attenuation of LMF. Meanwhile, ISMT can isolate the surface conditions of the specimen to avoid the formation of pseudo-magnetic particle indication (PMPI). The enhancement principle of ISMT is analyzed by simulation. Comparative experiments between ISMT and traditional MT were conducted to verify the visual enhancement effect of ISMT on defects of multiple depths. The results show that the enhancement effect of ISMT is 1.51 times, 1.36 times, and 1.08 times for the standard test shims of 60/100, 30/100, and 15/100, respectively. In addition, the advantage of ISMT in detecting larger defects is verified by experiments on hole defects of different sizes, and the isolation effect against surface oil stains is discussed.