Mikio Isozaki

Mikio Isozaki

Auto-generated profile, based on publicly available information

Mikio Isozaki

Japan Atomic Energy Agency

Research Focus & Metrics

Academic Career Length

14Years (2013-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
21 February 2013 in Journal of Engineering for Gas Turbines and Power
Verified
Journal Article
Closed access
PDF file
KMKen-Ichi Matsuba
Ken-Ichi Matsuba
MIMikio Isozaki
Mikio Isozaki
KKKenji Kamiyama
Kenji Kamiyama
YTYoshiharu Tobita
Yoshiharu Tobita
The elimination of severe power excursion during core disruptive accidents is a key issue for the enhanced safety of sodium-cooled fast reactors. In order to prevent the formation of a large-scale molten fuel pool within a reactor core, which is one of the factors leading to the severe power excursion, the Japan Atomic Energy Agency (JAEA) is considering the introduction of fuel assembly with inner duct structure (FAIDUS). In the current reference design for FAIDUS, the top end of the inner duct is open, whereas the bottom end is closed, and therefore it is expected that the molten fuel will be discharged from the reactor core towards the upper sodium plenum through the inner duct. The objective of the present study is to clarify the fundamental mechanism for upward fuel discharge through the inner duct structure, and thereby to confirm the effectiveness of FAIDUS. The possibility of upward discharge of a high-density melt driven by coolant vapor has been confirmed by the JAEA's experiment, in which molten Wood's metal simulating the molten fuel was injected into a coolant channel (equivalent inner diameter: 30 mm, total height: 2 m, fluid content: water) simulating the inner duct structure. In this paper, the mechanism of upward discharge of a high-density melt driven by coolant vapor pressure and/or flow in this experiment is discussed in terms of the application to reactor conditions. Through this discussion, the following mechanisms were clarified. (1) Coolant vapor pressure is built up within the coolant channel after the melt injection. The magnitude of the pressure buildup becomes larger with the increase of melt-enthalpy-injection rate, which is defined by the product of melt-mass-injection rate into the coolant channel and melt specific enthalpy. (2) Following the pressure buildup, the melt is discharged upward, being driven by the coolant vapor flow directing towards the top opening end of the coolant channel. The upward discharge mass rate becomes higher with the increase of the magnitude of the pressure buildup and, therefore, the melt-enthalpy-injection rate. The experimental knowledge obtained from the JAEA's experiment suggests that the coolant pressure buildup could act as one of the driving forces for the upward discharge of a high-density melt through the inner duct structure in FAIDUS under reactor conditions with higher melt-enthalpy-injection rate than the current simulant experimental condition.

1 January 2015 in The Proceedings of the International Conference on Nuclear Engineering (ICONE)
Verified
Journal Article
Closed access
PDF file
SCSongbai Cheng
Songbai Cheng
KMKen-Ichi Matsuba
Ken-Ichi Matsuba
MIMikio Isozaki
Mikio Isozaki
KKKenji Kamiyama
Kenji Kamiyama
TSTohru Suzuki
Tohru Suzuki
YTYoshiharu Tobita
Yoshiharu Tobita
Analyses of severe accidents for sodium-cooled fast reactors have shown that by assuming pessimistic conditions the accident might proceed into a transition phase where a large whole-core-scale pool containing sufficient fuel to exceed prompt criticality by fuel compaction might be formed. Local fuel-coolant interaction (FCI) in the pool is regarded as one of the probable initiators that could lead to such compactive fluid motions. To enhance the evaluation of severe accidents, a three-step research plan has been determined. In Phase 1, a series of simulated experiments, which covers a variety of conditions including much difference in water volume, melt temperature, water subcooling and water release site, was conducted by delivering a given quantity of water into a molten pool formed with a low-melting-point alloy, while in Phase 2, the interaction characteristics (esp. the pressure buildup) was investigated using the SIMMER-III, an advanced fast reactor safety analysis code. It was recognized that the SIMMER-III code, with its existing heat-transfer models, can reasonably reproduce the experimental evidence observed, thereby greatly stimulating us to initiate the Phase 3, in which further numerical analyses using reactor materials are planned. In this work, based on the latest calculations, it is confirmable that similar to the observations in Phases 1 and 2, for a given melt and sodium temperature within the non-film boiling condition, as the volume of sodium entrapped within the pool increases, a limited pressure-buildup is achievable. In addition, the performed analyses also suggest that despite of a comparatively larger temperature range of molten-fuel and sodium possibly varied during reactor accident progression, the isolation effect of vapor bubbles generated at the melt-sodium interface seems to be the unique dominant mechanism that leads to such limited pressurization. Knowledge and fundamental data from this work might be utilized for future empirical-approach studies (e.g. a lookup table for estimating the critical coolant volume required for achieving the saturated pressurization at varied melt and coolant temperatures).