30 July 2010 in Geophysical Journal International
Summary. For the first time, a comparative analysis of the resolution and variance properties of 2-D models of electrical resistivity derived from single and j
7 January 2020 in Earth, Planets and Space
3D inversions of magnetotelluric data are now almost standard, with computational power now allowing an inversion to be performed in a matter of days (or hours) rather than weeks. However, when compared to 2D inversions, these are still very computationally demanding. As a result, 3D inversions are generally not subjected to as rigorous testing as a 1D or 2D inversion would be, which has implications when these models are used for geological interpretation. In this study, we explore the parameter space for inversion of continent-scale datasets. The generalisations made regarding the effects of each parameter should also be scalable to smaller surveys and will enable MT practitioners to optimise their results. We have performed testing on a subset of the South Australian component of the eventual Australia-wide AusLAMP (Australian Lithospheric Architecture Magnetotelluric Project). The subset was inverted with different parameters, model setup and data subsets. Specifically, results from testing of the model covariance, the resistivity of the prior model, the inclusion of 'known' information into the prior model, the model cell size, the data components inverted for and the damping parameter $$\lambda $$ were all investigated. In our testing of the 3D inversion software, ModEM3DMT, we found that the resistivity of the starting/prior model had significant effect on the final model. Careful selection of initial $$\lambda $$ value can aid in reducing computational time whilst having a negligible effect on the resultant model, whilst large covariance values and model cell sizes enhanced conductive features at depth.
4 April 2019 in Journal of Geophysical Research: Solid Earth
We present a model of the electrical resistivity structure of the lithosphere in the Central Andes between 20° and 24°S from 3‐D inversion of 56 long‐period magnetotelluric sites. Our model shows a complex resistivity structure with significant variability parallel and perpendicular to the trench direction. The continental forearc is characterized mainly by high electrical resistivity (>1,000 Ωm), suggesting overall low volumes of fluids. However, low resistivity zones (LRZs, 1,000 Ωm and the absence of active volcanism, suggesting the presence of a low‐permeability block in the continental crust. The central domain (20.5°–23°S) exhibits a number of LRZs at varying depths, indicating different levels of a magmatic plumbing system. The southern domain (23°–24°S) is characterized by resistivities >1,000 Ωm, suggesting the absence of large magma reservoirs below the volcanic chain at crustal depths. Magma reservoirs located below the base of the crust or in the backarc may fed active volcanism in the southern domain. In the subcontinental mantle, the model exhibits LRZs in the forearc mantle wedge and above clusters of intermediate‐depth seismicity, likely related to fluids produced by serpentinization of the mantle and eclogitization of the slab, respectively.
29 October 2015 in Geophysical Prospecting
27 September 2016 in Geophysical Journal International
We report on a study to explore the deep electrical conductivity structure of the Dead Sea Basin (DSB) using magnetotelluric (MT) data collected along a transect across the DSB where the left lateral strike-slip Dead Sea transform (DST) fault splits into two fault strands forming one of the largest pull-apart basins of the world. A very pronounced feature of our 2-D inversion model is a deep, subvertical conductive zone beneath the DSB. The conductor extends through the entire crust and is sandwiched between highly resistive structures associated with Precambrian rocks of the basin flanks. The high electrical conductivity could be attributed to fluids released by dehydration of the uppermost mantle beneath the DSB, possibly in combination with fluids released by mid- to low-grade metamorphism in the lower crust and generation of hydrous minerals in the middle crust through retrograde metamorphism. Similar high conductivity zones associated with fluids have been reported from other large fault systems. The presence of fluids and hydrous minerals in the middle and lower crust could explain the required low friction coefficient of the DST along the eastern boundary of the DSB and the high subsidence rate of basin sediments. 3-D inversion models confirm the existence of a subvertical high conductivity structure underneath the DSB but its expression is far less pronounced. Instead, the 3-D inversion model suggests a deepening of the conductive DSB sediments off-profile towards the south, reaching a maximum depth of approximately 12 km, which is consistent with other geophysical observations. At shallower levels, the 3-D inversion model reveals salt diapirism as an upwelling of highly resistive structures, localized underneath the Al-Lisan Peninsula. The 3-D model furthermore contains an E–W elongated conductive structure to the northeast of the DSB. More MT data with better spatial coverage are required, however, to fully constrain the robustness of the above-mentioned off-profile features.
10 February 2020 in Earth, Planets and Space
The Lorca earthquake (May 11th, 2011, Mw 5.2) stands as the most destructive one in Spain over the last 50 years, interpreted as having occurred in an intersegment zone of the strike–slip Alhama de Murcia Fault (AMF) (Eastern Betics, Spain). Magnetotelluric data were acquired along a profile to the SW of Lorca (La Torrecilla profile), to characterize its signature at depth, as part of the multidisciplinary project “INTERGEOSIMA”. Given the short distance between stations, some station pairs were recorded simultaneously, with magnetic sensors in only one of them. In order to properly understand the resulting impedances (called interstation impedances), and the effects of inverting them, we used synthetic models to compare the impedances and the interstation impedances and to analyze the corresponding inversion results, together with the inversion of the quasi-impedance (inversion of the interstation impedances, considering them as impedances). The results are sensitive to the location of the magnetic sensors and the resistivity underneath, but in general the use of the quasi-impedances in the inversion can be considered a valid procedure. Both the 2D and the 3D resistivity models obtained through the inversion allowed us to complement the previous ERT models and represent the continuation of the main fault gouge in depth showing its extension towards the SE.