5 February 2020 in IEEE Transactions on Industrial Electronics
A simple and efficient single-phase direct AC to AC converter with the possibility to be utilized as a voltage buck or buck-boost converter is proposed in this paper. The proposed converter offers higher efficiency than the competitors with a lower number of semiconductors. The proposed switching strategy minimizes the high frequency operation and simultaneous conduction of semiconductors during each mode of operation. Besides a higher efficiency, the other major advantages of the proposed converter can be mentioned as eliminating the risk of input source shoot-through, a lower number and total rating of semiconductors, defined by switching device power (SDP) parameter, a lower number and smaller size of reactive components, a better input current quality and lower filtering requirements. The theoretical claims are confirmed through experiments on a 480W prototype built in laboratory.
27 May 2022 in IEEE Transactions on Power Electronics
The Y-source impedance network is truly referred to as the origin of the magnetically coupled impedance source inverters. The key characteristics, including high boost capability and design flexibility, are associated with the coupled inductor turn ratio. However, the magnetic element brings some practical challenges, such as voltage spikes, high shoot-through (ST) current, and bulky coupled inductors. This article proposes two new Y-source inverters with clamped dc-link voltage. Due to the high boost ability, they are suitable for single-stage high gain inversions. Additionally, the significant reduction in the amplitude of the ST current leads to a reduction of the total power loss and capacity of the reactive component. Another attractive characteristic is that the Y-shaped coupled inductor's stored energy is no longer affected by the power rating of the converter, as a result of the zero dc magnetizing current. All these contribute to the high efficiency and power density of the proposed converters. The design guidelines of the components are presented and a thorough comparison with the state of the art is carried out. The achievements are then confirmed through extensive tests on a 500 W laboratory setup.
12 September 2022 in IEEE Transactions on Power Electronics
The use of coupled inductors in impedance source inverters improves the voltage gain performance at the expense of high dc-link voltage spikes and shoot-through (ST) currents. The result is an increase in voltage and current stresses on semiconductors, as well as reactive element capacity and overall losses. Thus, to overcome these problems, this letter proposes a new family of magnetically coupled impedance source inverters with a smooth dc-link voltage, a low ST current, and a higher voltage gain that are confirmed through experimental tests.
31 December 2020 in IET Power Electronics
This paper proposes a class of impedance networks, called quasi‐Δ‐source, as an improvement to the successful Δ‐source one. Compared to their origin, the three proposed networks offer higher voltage gains with a better magnetic circuit utilization and a smooth continuous input current. A lower magnetizing and total inductance required for the Δ‐shaped coupled inductors of the proposed networks allows smaller and cheaper magnetic cores utilization. Also, a lower total power loss of the magnetically coupled elements is another interesting advantage of the proposed networks. Moreover, the total required capacitance of the proposed networks is the same and even slightly lower than that of the conventional Δ‐source one. All these improve the performance of the proposed class of networks with the smaller size of components compared to their conventional competitor. The principles of operation are developed and the theoretical analysis is performed. Also, by using the circuit averaging technique, the small‐signal models of the Δ‐source and the proposed networks are derived as well as their control‐to‐output transfer function is achieved. Finally, the experiments on a 300 W rated power prototype of the proposed networks successfully confirm the theoretical achievements.
8 April 2024 in IEEE Transactions on Circuits and Systems II: Express Briefs
This paper proposes an isolated DC-DC converter with a highly flexible voltage gain, which can be adjusted by three independent parameters. The proposed converter also offers the smooth input current, a simple structure and high efficiency. The only switch of the converter experiences extremely low voltage spikes; its output diode works under the zero current switching (ZCS), leading to reduced switching losses and overall converter costs. Low magnetizing current of coupling inductors and low voltage stress of capacitors of this converter indicates its high power density. The input current ripple reduction technique is independent of the coupling factor and can be easily implemented in the converter. The operating principle and parameter design guideline of the proposed converter are explained in detail, and its performance is compared with two existing DC-DC converters. To further validate the proposed converter, a 400 W prototype is built and tested in the laboratory.