In this paper, the modeling of an optimum fast charging profile for lead-acid batteries (LABs) is proposed. The proposed profile is a multi-step constant current (MSCC) where various current magnitudes in a descending manner are applied to the battery; therefore, it prevents the over-voltage and gassing phenomenon at the end of charging process, and shortens the charging time at the same time. Using an electro-thermal model of a LAB, an optimization problem containing charging time, battery temperature during the process, and battery's terminal voltage as objective functions is defined. The magnitude and duration of all charging steps are taken into account as control variables to be optimized for minimizing the objective functions using a particle swarm optimization (PSO) algorithm. A comparison between different conventional charging profiles for LABs is also provided in terms of charging time and battery's temperature and voltage. The simulation results carried out by MATLAB/Simulink show that the proposed profile reduces the charging time, while keeps the battery's temperature and voltage during the charging process within allowable range. The impacts of model's uncertainties on the proposed approach is evaluated. A comprehensive comparison is also provided to confirm the benefits of the proposed method over MSCC profiles reported in the literature. The effectiveness of the proposed approach is finally validated using the experimental implementation for a 12V 200Ah lead-acid battery.
This paper proposes a class of impedance networks, called quasi‐Δ‐source, as an improvement to the successful Δ‐source one. Compared to their origin, the three proposed networks offer higher voltage gains with a better magnetic circuit utilization and a smooth continuous input current. A lower magnetizing and total inductance required for the Δ‐shaped coupled inductors of the proposed networks allows smaller and cheaper magnetic cores utilization. Also, a lower total power loss of the magnetically coupled elements is another interesting advantage of the proposed networks. Moreover, the total required capacitance of the proposed networks is the same and even slightly lower than that of the conventional Δ‐source one. All these improve the performance of the proposed class of networks with the smaller size of components compared to their conventional competitor. The principles of operation are developed and the theoretical analysis is performed. Also, by using the circuit averaging technique, the small‐signal models of the Δ‐source and the proposed networks are derived as well as their control‐to‐output transfer function is achieved. Finally, the experiments on a 300 W rated power prototype of the proposed networks successfully confirm the theoretical achievements.
14 July 2025 in IEEE Open Journal of the Industrial Electronics Society
The expansion of residential distributed generation systems relies heavily on single-phase inverters for grid integration. However, these inverter-based resources compromise grid stability, mainly due to a lack of inertia and grid strength. To address these issues, grid-forming inverters have been developed, with virtual oscillator control (VOC) emerging as a promising approach due to its superior dynamic performance. However, basic VOC-based inverters cannot provide inertial functionality. Attempts to incorporate virtual inertia into VOCs have significantly reduced the damping factor and led to severe dynamic oscillations. This paper presents a novel technique to improve the dynamic response of single-phase VOC-based inverters by enhancing damping without affecting the virtual inertia and droop functionalities. The effectiveness of the proposed approach is validated through small-signal analysis and extensive experimental testing on a 2.5 kVA single-phase inverter. The results confirm the small-signal model with well-damped dynamic responses in gridconnected mode, without degrading system inertia during stand-alone operation.
The increasing penetration of renewable energy and electric vehicles (EVs) has intensified the need for grid-forming (GFM) inverters capable of supporting frequency and voltage stability. Virtual Oscillator Control (VOC) has recently emerged as a promising time-domain GFM strategy due to its fast dynamics and autonomous synchronisation capability. This paper presents a comprehensive analysis of recent VOC developments, focusing on the Andronov–Hopf Oscillator (AHO) and its variants. A comparative overview of different VOC structures highlights their capabilities in providing essential services such as dispatchability, fault ride-through (FRT), virtual inertia, and damping. A generalised small-signal state-space model is developed to assess the influence of virtual inertia, grid impedance, and control parameters on transient performance, which is essential for optimal parameter design and controller tuning in various applications. Experimental validation using a 2.5 kVA single-phase inverter shows excellent agreement with theoretical predictions. The results confirm that while increased virtual inertia enhances frequency stability, it also introduces oscillations that can be effectively mitigated through damping enhancement. Furthermore, the experiments demonstrate that advanced AHO-based strategies successfully deliver vehicle-to-grid (V2G) and vehicle-to-home (V2H) services, confirming their practical applicability in future EV-integrated and renewable-rich power systems.
This paper proposes a wide range high step-down gain flyback power factor correction rectifier (PFC) based on the flyback DC-DC converter. The proposed rectifier is composed of a step-down Z-source network at the AC to DC stage, followed by a flyback chopper. The proposed PFC rectifier offers better input and output waveform qualities in comparison to the conventional buck-boost and flyback PFC rectifiers, because of continuous input current. Also, it ensures high power factor (PF) operation and low harmonic contents over a wide range of load and source variations with galvanic isolation. These features are practically of interest for a battery charging system. Furthermore, the proposed PFC rectifier allows for increasing the switching frequency due to a higher duty cycle possible for the same voltage gain than the competitors. Finally, the unity power factor operation is simply possible by just using a simple single loop voltage controller. A test bench of the proposed PFC rectifier is designed for performance evaluation in PLECS software. Also, the performance of the converter is experimentally confirmed by tests on a 230 V rms to 48 V dc rated at 200-W laboratory prototype.