Matteo Felice Iacchetti

Matteo Felice Iacchetti

Auto-generated profile, based on publicly available information

Matteo Felice Iacchetti

Department of Electrical and Electronic Engineering, The University of Manchester, Manchester, U.K.

Research Focus & Metrics

Academic Career Length

20Years (2007-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
24 April 2018 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
GMGil Domingos Marques
Gil Domingos Marques
MIMatteo Felice Iacchetti
Matteo Felice Iacchetti
The Doubly Fed Induction Machine has been traditionally adopted in adjustable-speed ac power generation drives in order to take advantage of the reduced rating for the power electronic interface. Aside this well-established application where the DFIG is controlled by a back-to-back converter, recent literature records a growing interest towards un-conventional DFIG drives for dc power generation, combining DFIG high control freedom with simplified power electronic interfaces to achieve an overall cheap and fully-controllable system. Despite several concepts have been demonstrated on small-scale rigs, there is a lack of systematic comparison among different topologies and control solutions. This paper bridges this gap by providing a review of recent topologies, their control, design and performance, and operation issues. As major novelties the paper includes off-spec performance comparison of different torque-ripple mitigation strategies and discussion of sizing requirements for generator and power electronics, fundamental aspects of the behavior under voltage dips, and priorities and challenges for future research on the subject.

9 March 2018 in IEEE Transactions on Applied Superconductivity
Verified
Journal Article
Closed access
CMCharalampos D. Manolopoulos
Charalampos D. Manolopoulos
MIMatteo F. Iacchetti
Matteo F. Iacchetti
ASAlexander C. Smith
Alexander C. Smith
Kévin BergerKévin Berger
Kévin Berger
MHMark Husband
Mark Husband
PMPaul Miller
Paul Miller
Hybrid electric propulsion has been identified as a potential solution to the ambitious environmental emissions and noise targets of the aerospace industry. Superconducting machines may be the key component of that topology enabling the high power densities and efficiencies needed in aerospace. Fully superconducting machines, however, are not a mature technology. This paper looks at the different machine design configurations focusing on the stator magnetic circuit of a fully superconducting motor. The motor has been designed for an aerospace distributed fan propulsion motor with an aerospace benchmark specification of 1 MW. The AC fully superconducting machine includes superconducting bulk magnets mounted on a conventional rotor core and an MgB$_{2}$ superconducting wire wound stator. The AC losses in the stator winding are particularly sensitive to exposure to the main rotor field so different screening solutions were used to shield the superconducting windings from the rotor field. The effectiveness of the screening techniques for the stator coils and the impact on the machine performance and weight were evaluated for different stator designs, such as full stator core and air core with and without flux diverters. Various combinations of pole numbers, diverter geometries and magnetic materials have been checked. Results show that there is a trade-off between stator iron losses and superconducting losses.

1 September 2014 in IET Electric Power Applications
Verified
Journal Article
Open access
PDF file
MIMatteo F. Iacchetti
Matteo F. Iacchetti
GMGil D. Marques
Gil D. Marques
RPRoberto Perini
Roberto Perini
The operation of a doubly fed induction generator (DFIG) connected to a dc net is considered in this study. The dc net is connected to the stator of the DFIG by a diode rectifier and simultaneously feeds the rotor‐side inverter, which is used to control the machine. When the dc net operates at constant voltage, this solution preserves the possibility to work with a low flux at low speed, and, at the same time, reduces the cost of the power electronics. In fact, the only needed electronic converter is the rotor inverter designed for a fraction of the machine power. After introducing a simple control technique, the study proposes an analytic model for the steady‐state operation and discusses the design specifications of the DFIG for given values of the dc voltage and of the power of the wind turbine. The most appropriate stator and rotor rated powers, rated stator voltage and turns ratio of the DFIG are deduced. Simulations and experimental results are presented in order to support the theory.

22 March 2018 in IEEE Transactions on Industrial Electronics
Verified
Journal Article
Closed access
Sérgio CruzSérgio Cruz
Sérgio Cruz
GMGil D. Marques
Gil D. Marques
Pedro F. da Costa GonçalvesPedro F. da Costa Gonçalves
Pedro F. da Costa Gonçalves
MIMatteo Felice Iacchetti
Matteo Felice Iacchetti
The severe torque ripple normally occurring in the DFIG-dc system can cause premature failure of mechanical components and shorten the life of the drive train. This paper addresses the torque ripple issue by proposing a predictive direct torque control strategy which delivers at the same time torque ripple suppression and minimization of losses. The existing control algorithms for torque ripple mitigation are mostly based on resonant controllers and repetitive control forcing the compensation signal either through the current chain or directly into the rotor voltage commands. All these techniques lead to structures with multiple controllers whose tuning is not straightforward. Furthermore, they are very sensitive to the operating frequency, making optimized operation with variable frequency highly challenging. Conversely, the proposed algorithm predicts directly the best rotor voltage space vector to minimize torque ripple and track a prescribed rotor flux amplitude to minimize losses, with no current control chain. As confirmed by simulations and experiments, the strategy allows large stator frequency variations as required by the optimal flux command for minimum losses, whilst ensuring effective torque ripple compensation.

1 November 2013 in IET Power Electronics
Verified
Journal Article
Open access
PDF file
AGAntonino Di Gerlando
Antonino Di Gerlando
GFGiovanni Maria Foglia
Giovanni Maria Foglia
MIMatteo F. Iacchetti
Matteo F. Iacchetti
RPRoberto Perini
Roberto Perini
This study deals with the analytical modelling of the steady‐state operation of a three‐phase diode rectifier whose dc bus is connected to a constant voltage source. Such a system exhibits several operation modes that are fully investigated. Analytical expressions of the boundaries of each mode as well as the average dc and the rms ac currents are deduced as a function of the ac and dc parameters, including voltage drops across diodes. They allow us to evaluate the power delivered to the dc bus as well as the efficiency of the conversion in each mode of operation. These results can also be extended to practical rectifiers with bulk dc capacitors and allow for performing parametric analyses and optimisation in the design of drives or permanent magnet synchronous generators directly connected to a diode rectifier. The theoretical results are validated by experimental tests.

10 September 2018 in IEEE Transactions on Energy Conversion
Verified
Journal Article
Closed access
IEInaki Erazo-Damian
Inaki Erazo-Damian
JAJudith M. Apsley
Judith M. Apsley
RPRoberto Perini
Roberto Perini
MIMatteo F. Iacchetti
Matteo F. Iacchetti
GMGil Domingos Marques
Gil Domingos Marques
Inaccurate machine parameters can cause orientation errors and instability in field oriented control schemes relying on model-based estimations. This paper analyzes the accuracy and stability of two field oriented control schemes for a stand-alone DFIG, where the field orientation is affected by the stator inductance and stator/mutual inductance ratio. After deriving a reduced-order model accounting for parameter mismatch, the paper deduces a formula to calculate the field orientation error as a function of the inductance mismatch, revealing parameter sensitivities. A stability analysis is then carried out proving that overestimating the stator/magnetizing inductance ratio may trigger instabilities in case of high load level, whereas underestimation allows always stable operation. The theoretical insight is supported with simulation and test results on a laboratory rig.