Cheng-Jung Lee

Cheng-Jung Lee

Auto-generated profile, based on publicly available information

Cheng-Jung Lee

Institute of Microelectronics, Department of Electrical Engineering, National Cheng-Kung University, Tainan 701, Taiwan

Research Focus & Metrics

Academic Career Length

21Years (2006-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 2019 in IEEE Electron Device Letters
Verified
Journal Article
Closed access
CLCheng-Jung Lee
Cheng-Jung Lee
YCYu Chi Chang
Yu Chi Chang
LWLi-Wen Wang
Li-Wen Wang
YWYeong-Her Wang
Yeong-Her Wang

1 June 2006
Verified
Conference Paper
Closed access
CLCheng-Jung Lee
Cheng-Jung Lee
KLKevin M. K. H. Leong
Kevin M. K. H. Leong
TITatsuo Itoh
Tatsuo Itoh
This paper presents a methodology of designing a microwave bandstop filter and a bandpass filter by using a Composite Right/Left Handed transmission line (CRLH-TL) as part of a transversal filter. The CRLH-TL can be engineered to have specific phase slope and phase offset. Connecting the CRLH-TL and the conventional microstrip delay line at both input and output can establish a transversal filter where the signal merging at the output has broadband out of phase characteristics. Therefore, the bandstop filter can be created with signal rejection over a wide frequency range. The measured 3dB bandwidth of the bandstop filter is 130% and the minimum insertion loss at the next passband is -1.7dB. In addition, based on the bandstop filter a bandpass filter with a wide signal rejection range is developed by creating a frequency dependent defect in one branch of the bandstop filter. This is implemented by either attaching a microstrip open stub or capacitively coupling a microstrip resonator to the microstrip delay line. The 3dB passband bandwidth and the minimum insertion loss are 18%, -1.5dB and 8%, -2dB corresponding to the open stub and the resonator scheme, respectively

26 December 2017 in Materials
Verified
Journal Article
Open access
PDF file
CLCheng-Jung Lee
Cheng-Jung Lee
YCYu Chi Chang
Yu Chi Chang
LWLi-Wen Wang
Li-Wen Wang
YWYeong-Her Wang
Yeong-Her Wang
This study investigates the preparation and electrical properties of Al/cobalt-embedded gelatin (CoG)/ indium tin oxide (ITO) resistive switching memories. Co. elements can be uniformly distributed in gelatin without a conventional dispersion procedure, as confirmed through energy dispersive X-ray analyzer and X-ray photoelectron spectroscopy observations. With an appropriate Co. concentration, Co. ions can assist the formation of an interfacial AlOx layer and improve the memory properties. High ON/OFF ratio, good retention capability, and good endurance switching cycles are demonstrated with 1 M Co. concentration, in contrast to 0.5 M and 2 M memory devices. This result can be attributed to the suitable thickness of the interfacial AlOx layer, which acts as an oxygen reservoir and stores and releases oxygen during switching. The Co. element in a solution-processed gelatin matrix has high potential for bio-electronic applications.

9 December 2017 in Materials
Verified
Journal Article
Open access
PDF file
KLKe-Jing Lee
Ke-Jing Lee
YCYu Chi Chang
Yu Chi Chang
CLCheng-Jung Lee
Cheng-Jung Lee
LWLi-Wen Wang
Li-Wen Wang
YWYeong-Her Wang
Yeong-Her Wang
A one-transistor and one-resistor (1T1R) architecture with a resistive random access memory (RRAM) cell connected to an organic thin-film transistor (OTFT) device is successfully demonstrated to avoid the cross-talk issues of only one RRAM cell. The OTFT device, which uses barium zirconate nickelate (BZN) as a dielectric layer, exhibits favorable electrical properties, such as a high field-effect mobility of 2.5 cm2/Vs, low threshold voltage of −2.8 V, and low leakage current of 10−12 A, for a driver in the 1T1R operation scheme. The 1T1R architecture with a TiO2-based RRAM cell connected with a BZN OTFT device indicates a low operation current (10 μA) and reliable data retention (over ten years). This favorable performance of the 1T1R device can be attributed to the additional barrier heights introduced by using Ni (II) acetylacetone as a substitute for acetylacetone, and the relatively low leakage current of a BZN dielectric layer. The proposed 1T1R device with low leakage current OTFT and excellent uniform resistance distribution of RRAM exhibits a good potential for use in practical low-power electronic applications.