Artem Krasota

Artem Krasota

Auto-generated profile, based on publicly available information

Artem Krasota

Central Ukrainian National Technical University

Research Focus & Metrics

Academic Career Length

2Years (2025-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
26 May 2025 in Central Ukrainian Scientific Bulletin. Technical Sciences
Verified
Journal Article
Closed access
ISIhor Shepelenko
Ihor Shepelenko
AKArtem Krasota
Artem Krasota
VGVasiliy Gutsul
Vasiliy Gutsul
MKMykhailo Krasota
Mykhailo Krasota
Ihor Shepelenko, Professor, Doctor of Technical Science, professor of the Department of Exploitation and repairing machines, Central Ukrainian National Technical University, Kropyvnytskyi, Ukraine, https://orcid.org/0000-0003-1251-1687, e-mail: kntucpfzk@gmail.com Artem Krasota, PhD student in Industrial Engineering, Central Ukrainian National Technical University, Kropyvnytskyi, Ukraine, ORCID: https://orcid.org/0009-0007-7700-9176, e-mail: kras.365@gmail.com Vasiliy Gutsul, Associate Professor, Candidate of Technical Sciences, Associate Professor of the Department of Higher Mathematics and Physics, Central Ukrainian National Technical University, Kropyvnytskyi, Ukraine, ORCID: https://orcid.org/0000-0003-4155-5355, e-mail: vigutsul@ukr.net Mykhailo Krasota, Associate Professor, Candidate of Technical Sciences, associate professor of the Department of Exploitation and repairing machines, Central Ukrainian National Technical University, Kropyvnytskyi, Ukraine, ORCID: https://orcid.org/0000-0001-8791-3264, e-mail: krasotamv@ukr.net An analysis of traditional friction-mechanical antifriction coating application schemes, as well as devices for their implementation, have shown their effectiveness in treating surfaces of parts with the shape of a body of revolution. However, for machining complex profile surfaces, which include camshaft cams, the use of such schemes is unacceptable due to the lack of stable contact between the tool and the part. The aim of the presented work is to substantiate the design and develop a device for finishing antifriction non-abrasive machining of camshaft cams by friction-mechanical method. The ways to achieve the goal are determined - to provide the necessary trajectory of movement of the tool or part, which copies the shape of the cam and creates the necessary conditions for the qualitative implementation of the selective transfer of antifriction material to the working surface of the part. This can be achieved through the use of a lever-type tool loading scheme that ensures a constant tool pressure force on the cam surface, taking into account its geometry. The proposed approach made it possible to develop the design of a device for applying antifriction coatings with a finishing antifriction non-abrasive treatment to the working surface of camshaft cams. Another approach to solving this problem is to use the design of a device containing copying and rubbing units. The presence of copiers in the proposed device ensures the creation of reciprocating and rotational movement of the tool along a trajectory corresponding to the shape of the cam with the required stable force. The justification of the device designs allows us to assert the possibility of providing high-quality conditions for the finishing antifriction non-abrasive machining of camshaft cams. Experimental studies that require the manufacture of the device and testing in laboratory or production conditions will allow you to choose the most effective design from the two options.

23 December 2025 in National Interagency Scientific and Technical Collection of Works. Design, Production and Exploitation of Agricultural Machines
Verified
Journal Article
Closed access
ISIhor Shepelenko
Ihor Shepelenko
AKArtem Krasota
Artem Krasota
VGVasiliy Gutsul
Vasiliy Gutsul
MKMykhailo Krasota
Mykhailo Krasota
The presented studies are devoted to establishing the main patterns of stress state changes in the contact zone of the camshaft cam, the working surface of which is coated with an anti-friction coating. A method for studying the stress state of the cam working surface is proposed, which consists in selecting a calculation scheme that takes into account the operating conditions of the “cam-follower” connection, obtaining analytical dependencies for determining stresses in the contact zone, and their graphical interpretation to establish the main patterns. For the analytical study of the patterns of stress in the contact zone, the method of elasticity theory was used to solve contact problems. In this case, it was assumed that the cam and follower contact each other on a rectangular area. This made it possible to establish the main dependencies for determining the stress state in the studied zone. The calculation of circumferential and axial stresses made it possible to construct diagrams of their distribution for a cam with an anti-friction coating, as well as without an anti-friction coating. To analyze the causes of stress concentration peaks at the boundaries of the contact areas, calculations were made of the stress state of the cam surface, which is subjected only to friction stresses in the contact zone. Calculations of the stress state of the working surface of the camshaft of a KamAZ truck engine showed that compressive stresses arise in the circumferential direction, with their maximum reaching the central zone of the contact area. Tensile stresses are created at the edges of the contact area. It has been established that contact friction forces contribute to the appearance of stress peaks, the magnitude of which is related to the design features of the cam-follower friction pair of the camshaft. The calculations confirm the feasibility of using anti-friction coatings on the surfaces of camshaft cams. Applying such FANT coatings reduces stresses by 47% in the circumferential direction and 34% in the longitudinal direction, thereby reducing cam wear.

11 June 2026 in Central Ukrainian Scientific Bulletin. Technical Sciences
Verified
Journal Article
Open access
АКА. М. Красота
А. М. Красота
ІШІ. В. Шепеленко
І. В. Шепеленко
МКМ. В. Красота
М. В. Красота
РОР. А. Осін
Р. А. Осін
У статті представлені результати дослідження, спрямованого на покращення якості отримання антифрикційних покриттів під час використання фінішної антифрикційної безабразивної обробки кулачків розподільних валів автомобільних та тракторних двигунів. За критерії оптимізації було обрано умови якості антифрикційного покриття (суцільність, відносна шорсткість поверхні) та експлуатаційний показник – інтенсивність зношування зразка. Функціями відгуку були обрані режими ФАБО за визначеною схемою нанесення антифрикційних покриттів на робочу поверхню кулачків розподільних валів. Після проведення багатофакторного експерименту, на основі результатів, було отримано серію математичних моделей у вигляді рівнянь регресії. Аналіз математичних моделей дозволив визначити оптимальні змінні значення режимних параметрів ФАБО. Результати наданого дослідження дозволили визначити оптимальні режими ФАБО, а саме: тиск інструменту, швидкість ковзання інструменту та подача інструменту. При заданих оптимальних параметрах було отримано прогнозовані значення вихідних змінних: суцільності покриттів, інтенсивності зношування та відносної шорсткості. Встановлено, що зі збільшенням тиску до 60 МПа спостерігається зменшення інтенсивності зношування, проте подальше збільшення тиску має тенденцію до її зростання. При заданих швидкостях приблизно 2,0 м/с спостерігається збільшення суцільності покриття до досягнення максимальних значень, подальше збільшення швидкості ковзання негативно впливає на суцільність покриття через недостатнє заповнення мікрорельєфу та погане формування антифрикційного покриття. Збільшення подачі у всьому діапазоні негативно впливає на відносну шорсткість, тому під час обробки слід підтримувати мінімальні значення подачі.

30 April 2026 in Technology audit and production reserves
Verified
Journal Article
Open access
PDF file
ISIhor Shepelenko
Ihor Shepelenko
AKArtem Krasota
Artem Krasota
MKMykhailo Krasota
Mykhailo Krasota
IVIvan Vasylenko
Ivan Vasylenko
ASAndrey Solovuch
Andrey Solovuch
The object of this research is the process of inspecting the camshafts of internal combustion engines in the context of vehicle repair production. As the inspection of a camshaft is a highly labor-intensive process due to the need to measure a large number of its components, there is a pressing need to improve the efficiency of inspection work. An approach is proposed for inspecting components with multiple worn surfaces, which involves determining the wear on one surface and calculating the wear on another using a regression model that establishes a quantitative relationship between the wear on the surfaces. This allows for a significant reduction in the labor intensity of defect detection work without compromising the reliability of the technical condition assessment of the component. This approach has been implemented using the example of defect detection on the camshaft of a KamAZ lorry engine. A hierarchical diagram of the camshaft structure as a system, where its individual elements are subsystems, is examined. It is noted that, among the surfaces of the camshaft, the cams and journal necks are subject to the most intense wear. A statistical model of camshaft wear has been constructed in the form of a linear regression equation, establishing a quantitative relationship between the wear of the journal necks and the cams. The practical significance of the proposed approach lies in improving the efficiency of defect detection work by reducing the volume of measurements by a factor of 2.6, which reduces the labor intensity of defect detection by 40%. When inspecting a batch of 100 camshafts, this results in a saving of 3,200 measurements, or over 36 hours. The results of this research have practical significance and are important for automotive repair enterprises engaged in the repair of internal combustion engine components.