5 April 2010 in IEEE Electron Device Letters
In this letter, we present a study on the electrical behavior of phase-change memories (PCMs) based on a GeTe active material. GeTe PCMs show, first, extremely rapid SET operation (yielding a gain of more than one decade in energy per bit with respect to standard GST PCMs), second, robust cycling, up to 1 × 105, with 30-ns SET and RESET stress time, and third, a better retention behavior at high temperature with respect to GST PCMs. These results, obtained on single cells, suggest GeTe as a promising alternative material to standard GST to improve PCM performance and reliability.
1 November 2011 in Solid-State Electronics
23 January 2014 in IEEE Transactions on Electron Devices
A novel approach to optimize tunnel field-effect transistors (TFETs) by technology computer-aided design simulations is reported. The most interesting outcome of our design effort is a dual-metal-gate (DMG) TFET, which features an inverse subthreshold slope (SS) significantly over more than five orders of magnitude of drain current, with a minimum value of 6 mV/decade sustained across one drain-current decade or more. The DMG-TFET simultaneously fulfills both the low-standby-power off-state current and the high-performance on-state current at a supply voltage of 0.5 V. Therefore, 25% reduction of static power consumption is expected compared with the 2020 International Technology Roadmap for Semiconductors requirements for multigate transistors.
2 December 2014 in IEEE Transactions on Electron Devices
A dual-metal-gate (DMG) tunnel FET (TFET) integrating a heavily-doped pocket within the channel is optimized through TCAD simulations by considering quantization-induced bandgap widening. First, the performance penalty due to the reduced tunneling probability is estimated and next, device design options to minimize the negative impact of quantization on the DMG-TFET performance are assessed.
1 September 2009 in Journal of Applied Physics
Low-frequency noise has been experimentally characterized in the disordered insulating phase of chalcogenide-based phase-change memory (PCM) devices. An analytical model of noise based on the two-level systems (TLS) theory has been developed. In this framework we suggest that the origin of the noise in the conductivity of amorphous chalcogenides has to be ascribed to the TLS-induced fluctuations of the mean trap energy in the material. The model allows to quantitatively account for noise magnitude dependence on both voltage and temperature in the readout region of the memory device. Besides, our equations well describe the noise behavior as a function of the drift phenomenon, coherently with existing structural relaxation theories. Measurements and model results show that the noise-to-signal ratio (N/S) in the readout region of the cell is constant with respect to bias; hence there is no particular readout voltage that minimizes N/S. Furthermore, the analysis of noise data with cell scaling confirms that noise in PCMs is mainly due to the bulk properties of the chalcogenide employed rather than to interfacial effects.
1 January 2013 in IEEE Transactions on Nanotechnology
PGPierre-Emmanuel Gaillardon
Pierre-Emmanuel Gaillardon
+2
Emerging nonvolatile memories (eNVMs) such as phase-change random access memories (PCRAMs) or oxide-based resistive random access memories (OxRRAMs) are promising candidates to replace Flash and Static Random Access Memories in many applications. This paper introduces a novel set of building blocks for field-programmable gate arrays (FPGAs) using eNVMs. We propose an eNVM-based configuration point, a look-up table structure with reduced programming complexity and a high-performance switchbox arrangement. We show that these blocks yield an improvement in area and write time of up to 3× and 33×, respectively, versus a regular Flash implementation. By integrating the designed blocks in an FPGA, we demonstrate an area and delay reduction of up to 28% and 34%, respectively, on a set of benchmark circuits. These reductions are due to the eNVM 3-D integration and to their low on-resistance state value. Finally, we survey many flavors of the technologies and we show that the best results in terms of area and delay are obtained with Pt/TiO2/Pt stack, while the lowest leakage power is achieved by InGeTe stack.