20 October 2023 in Izvestiya Vuzov. Tsvetnaya Metallurgiya (Proceedings of Higher Schools. Nonferrous Metallurgy)
The study investigated the feasibility of oxidative leaching rhenium in the presence of hydrochloric acid from machining waste (grinding waste) derived from products made of ZhS-32VI, a nickel-based heat-resistant alloy containing rhenium. This was achieved through agitation leaching process. The grinding waste fraction size of –0.071 mm, which accounted for the highest yield (49.2 wt.%), was utilized in the experiments. The rhenium leaching process was conducted in two variations: in the first option, grinding waste was mixed with a hydrochloric acid solution at ~100 °C, followed by the addition of hydrogen peroxide to the leaching solution after it had cooled; in the second option, leaching was performed using a hydrochloric acid solution with the gradual addition of hydrogen peroxide solution. The highest degree of rhenium leaching (91.0 %) was achieved in the first option. In this case, the initial concentration of hydrochloric acid was 8 M, and the molar ratio of the added reagents was ν(HCl): ν(H2O2) = 2.7 : 1.0. The kinetics of nickel leaching using a 6 M hydrochloric acid solution at 70 °C, with a solid-to-liquid phase ratio of 1 g : 50 ml, was also examined. The analysis of the kinetic data, processed using the “contracting sphere,” Ginstling–Brounshtein, and Kazeev–Erofeev models, indicates that the nickel leaching process occurs within the kinetic region. Additionally, the kinetics of rhenium leaching from the solid residue obtained after the hydrochloric acid leaching of nickel from grinding waste was investigated. Employing the same kinetic models to analyze the data, it was determined that the limiting stage of this process involves the diffusion of hydrogen peroxide within the rhenium-containing solid residue.
10 November 2025 in The Open Chemical Engineering Journal
Introduction: To address pressing resource and environmental challenges, this study investigates the tantalum recovery from a Ta-W semi-product generated during the processing of grinding waste from the ZhS32 VI rhenium-nickel superalloy. Methods: The Ta-W semi-product was sintered with NaOH (700–1000 °C) to oxidize TaC into insoluble sodium tantalates (NaTaO 3 /Na 5 TaO 5 ), with an optimal ratio (semi-product: NaOH) and temperature determined. The sintered residue underwent acid leaching (HF/H 2 SO 4 mixture, room temperature), where leaching parameters (time, phase ratio) were optimized; the kinetics was studied, and K 2 TaF 7 was precipitated from the leachate using KCl. Results: Minimum Ta extraction into solution during sodium hydroxide sinter leaching, along with complete transfer of W and Mo to the aqueous phase, is achieved at 700°C and a 1:3 (g/g) ratio. Subsequent leaching of the solid residue with an HF-H 2 SO 4 mixture (1 g: 1 mL: 1 mL) enables complete Ta recovery (>99.99%) within 30 minutes. The kinetics of tantalum acid leaching from the residue indicates a shift in the rate-limiting step from diffusion to chemical reaction. Through precipitation from the sulfate-fluoride solution using a KCl solution, Ta was obtained as K 2 TaF 7 (~52.64% Ta). Discussion: The presented process allows for the selective separation of tantalum from tungsten and molybdenum. The kinetics show a transition from diffusion to reaction, which enables efficient extraction at room temperature. Controlling impurities in K 2 TaF 7 requires further refinement. Conclusion: An effective two-stage hydrometallurgical process (alkaline sintering + acid leaching) enables high-yield tantalum recovery from superalloy grinding waste while facilitating valuable component recycling from heat-resistant alloy residues.
26 December 2025 in Transaction Kola Science Centre
This study investigates a sorption-based technology for recovering tantalum from sulfate-fluoride leaching solutions generated during the processing of tantalum-tungsten intermediate product derived from rhenium-nickel superalloy ZhS32 VI waste. The research aimed to develop an efficient method for reclaiming valuable tantalum from complex secondary raw materials. The methodology involved a comparative analysis of the efficiency of strongly basic anion exchange resins (Lewatit K6367, Axionit VPA G2.4, Purolite A600) under the following conditions: initial Ta concentration 4037 mg/L, 1 M H2SO4, 1 M HF, and solid-to-liquid ratio S:L — 1:50. It was found that the maximum tantalum recovery (85.3 %) was achieved using Lewatit K6367. Kinetic studies revealed different rate-determining steps: internal diffusion for the gel-type resin Axionit VPA G2.4 (k 8.99 g·mg-1·min-0.5), and chemical exchange reaction for the macroporous resins Purolite A600 and Lewatit K6367 (k 10.2·10-3 min-1 and 15.1·10-1 min-1, respectively). Desorption using an ammonium fluoride solution (100 g/L) recovered 85 % of the sorbed tantalum.