17 June 2020 in Avtoshliakhovyk Ukrayiny
HAHetman Petro Sahaidachny National Army Academy
Hetman Petro Sahaidachny National Army Academy
LULviv Polytechnic National University
Lviv Polytechnic National University
17 March 2021 in Системи озброєння і військова техніка
У статті визначено основні вимоги, які впливають на розвиток конструкцій зразків військової автомобільної техніки (ВАТ). Зокрема встановлено, що на підвищення швидкостей руху та мобільності колісної ВАТ при русі бездоріжжям загалом, впливають, як збільшення питомих потужностей двигунів, вибір оптимальних параметрів трансмісії, так і конструкції підвісок. Вібраційні та коливні навантаження на водія (екіпаж) зразків ВАТ під час руху бездоріжжям формують два визначальні аспекти застосування автомобілів. Перший аспект пов’язаний із штучним обмеженням водієм максимальної швидкості руху нижче технічної максимальної через граничну межу його дискомфорту, а другий - через відповідну втому і суттєве погіршення моторики водія (екіпажу) залежно від тривалості руху бездоріжжям. Визначено тенденцію розвитку конструкцій підвісок, яка полягає у переході від залежних підвісок з нерозрізною балкою осі і жорстким взаємозв’язком кінематики підвісок правого і лівого коліс до незалежних. Такий підхід дозволяє забезпечити підвищення комфортності в русі водія і екіпажу, а також підвищити середні швидкості руху та суттєво зменшити поперечні крени кузова. Проведено аналіз тенденцій впровадження активних і напівактивних підвісок на сучасних зразках колісної ВАТ, що дозволяє суттєво покращити комфортність екіпажу, збереженість вантажу та середні швидкості руху. За результатами досліджень встановлено необхідність переходу на довгоходові незалежні підвіски, для зменшення непідресорених мас та вібронавантаженості кузова і екіпажу.
8 June 2020 in Системи озброєння і військова техніка
У статті виконано порівняльний аналіз нормативних законодавчих баз країн НАТО та Росії щодо прохідності колісної військової автомобільної техніки (ВАТ) вимог та методів оцінки. Встановлено, що у країнах НАТО чинними є стандарти, які для експериментальної оцінки несної здатності опорних поверхонь (ОП) руху, ґрунтується на використанні конусного індексу СІ (англ. Сone index), який на відміну від характерного для України «радянського підходу», комплексно враховує вологість ґрунту, характеристики ОП театру бойових дій та дозволяє за допомогою стандартизованого програмного комп’ютерного забезпечення визначати найбільш раціональні маршрути і орієнтовні швидкості руху відповідних переміщень колісної ВАТ. Сформовано порогові значення показників опорної і профільної прохідності залежно від категорії та класу колісної ВАТ. Сформована класифікація ВАТ за прохідністю, яка дозволила розмежовувати класи за повною масою перспективних зразків колісної ВАТ та визначити порогові значення регламентованих показників профільної прохідності при яких забезпечується рух зразків колісної ВАТ: глибину броду, максимальні кути підйому та косогору, висоту порогової перешкоди, ширина рову (окопу). Опрацьовані методичні засади експериментальної оцінки опорної прохідності та визначення максимальних швидкостей руху ВАТ для найбільш характерних типів ОП. З метою визначення прохідності зразків колісної ВАТ за показником ММР (англ. Mean measure presure) методику його визначення удосконалено для врахування особливостей компоновки зразків колісної ВАТ. Сформовано основи національного стандарту ДСТУ-В “Військова автомобільна техніка. Прохідність та методи оцінки”.
31 August 2021 in Eastern-European Journal of Enterprise Technologies
This paper addresses the issue related to forecasting the durability indicators of public transport buses under operational conditions. It has been established that when buses are operated to transport passengers the bus bodies wear at different intensities. During operation, the strength of the body frame weakens under the influence of corrosion in combination with sites of fatigue destruction. As it was established, the intensity of corrosion of the bus body depends on the number of residents in the city where the bus is operated. The earlier established dependences were taken into consideration; the current study has identified two conditional variants of corrosion evolution based on the number of inhabitants: up to 1 million and exceeding 1 million. The expediency of repairs and their impact on the bus passive safety has been analyzed. It was found that the elements of the body frame, without external characteristic damage, no longer meet the specified conditions of strength as a result of sign-alternating loads and during long-term operation. Determining the durability of the bus body was made possible through the construction of a mathematical model. The model’s adequacy was confirmed by road tests of the bus. The devised model describes the movement of the bus over a road surface with different micro profiles, with different corrosion penetration, different loading by passengers, and bus speeds. It was established that the reason for the evolution of structural corrosion is the influence of salt mixtures preventing the icing of roads, as well as ignoring the washing of buses after such trips. It is recommended to use new software for the in-depth study into this issue addressing the combination of various factors of destruction: cyclic loads at variable bus speeds and the corrosion progress. The study results could make it possible to predict a life cycle of the body frame under factors that correspond to actual operating conditions.
30 April 2024 in Eastern-European Journal of Enterprise Technologies
The object of this study is the cross-country ability of four-wheel drive vehicles under off-road conditions. Based on the results of analysis of known studies, it was determined that the procedures of experimental assessment of the load-bearing capacity of bearing surfaces (BS), based on the use of the cone index, are used in NATO member countries. They take into account the characteristics of the surface of the theater of operations and make it possible to determine the approximate speeds of all-wheel drive vehicles with the help of standardized computer software. In the procedures for assessing the load-bearing capacity of BSs, which use the soil deformation module E, there is no possibility for calculating the speed of the car with known axle loads. In addition, they provide for the determination of a number of parameters of the bearing surface, such as the coefficient of adhesion, the angle of internal friction in the soil, and the shear modulus during the formation of a track. This makes them much more difficult compared to the procedures used by NATO. Therefore, the problem that is solved in this work is to improve the methodology for assessing the reference cross-country ability of four-wheel drive vehicles. Based on the results of scientific research, motion modeling was carried out in the MATLAB Simulink environment to determine parameters of reference cross-country ability of four-wheel drive vehicles. In order to determine the cross-country ability of samples of wheeled military vehicles (WMV) based on the indicator of the maximum pressure value (mean measure pressure – MMP), the conducted experimental studies were analyzed. They showed a difference in the speed modes of vehicles of the same gross weight but different layout schemes, within 11–12 %. Therefore, the methodology for assessing the cross-country ability based on MMP has been improved to take into account the features of the layout of WMV samples. Specifically, taking into account the different values of loads on the front axle of vehicles with hoodless and hood layouts at the same gross weight. In general, the improved procedure makes it possible to give a quantitative assessment of the movement mobility of WMV samples with various layout schemes and an assessment of their potential cross-country ability on the basis of the proposed refinement of MMP calculation
30 December 2022 in Eastern-European Journal of Enterprise Technologies
The object of this study is the permissible limits of aging of bus bodies during operation and the formation of appropriate recommendations to control them based on the conditions of compliance of the body with passive safety rules. According to the current method, the new model of the bus is checked for compliance with passive safety by a destructive method. However, during operation, the physical and mechanical properties of the body deteriorate until the moment of non-compliance with the requirements of passive safety. Therefore, the principles of technical control of bus bodies under the conditions of passive safety by non-destructive methods, the implementation of which became possible during the operation of buses, have been developed. 3 implementation options have been proposed. In the first variant, visual control is complemented by a measuring tool – an ultrasonic thickness gauge for measuring the thickness of the frame pipes. This method has not previously been used in the certification of vehicles. The second option involves checking the mechanical properties during repairs on a breaking machine. It is proved that during the restoration repairs of buses, the endurance limit of the steel elements of the body frame is reduced by 1.14–3.33 times. In the third variant, the methodology for modeling and calculating the stressed-strained state of the body was improved based on the method of finite elements, taking into account the effects of corrosion and fatigue strength of the metal of the frame. When modeling, the deformation of the body racks exceeded the permissible values by 1.5–2.0 times. This non-destructive method makes it possible to check the bus for compliance with passive safety requirements during operation, which was previously impossible. The scope of practical application is the introduction of research results into the real practice of operating buses at the legislative level. The results are suitable for monitoring the technical condition of buses by non-destructive methods during operation