30 April 2024 in Eastern-European Journal of Enterprise Technologies
The object of this study is the cross-country ability of four-wheel drive vehicles under off-road conditions. Based on the results of analysis of known studies, it was determined that the procedures of experimental assessment of the load-bearing capacity of bearing surfaces (BS), based on the use of the cone index, are used in NATO member countries. They take into account the characteristics of the surface of the theater of operations and make it possible to determine the approximate speeds of all-wheel drive vehicles with the help of standardized computer software. In the procedures for assessing the load-bearing capacity of BSs, which use the soil deformation module E, there is no possibility for calculating the speed of the car with known axle loads. In addition, they provide for the determination of a number of parameters of the bearing surface, such as the coefficient of adhesion, the angle of internal friction in the soil, and the shear modulus during the formation of a track. This makes them much more difficult compared to the procedures used by NATO. Therefore, the problem that is solved in this work is to improve the methodology for assessing the reference cross-country ability of four-wheel drive vehicles. Based on the results of scientific research, motion modeling was carried out in the MATLAB Simulink environment to determine parameters of reference cross-country ability of four-wheel drive vehicles. In order to determine the cross-country ability of samples of wheeled military vehicles (WMV) based on the indicator of the maximum pressure value (mean measure pressure – MMP), the conducted experimental studies were analyzed. They showed a difference in the speed modes of vehicles of the same gross weight but different layout schemes, within 11–12 %. Therefore, the methodology for assessing the cross-country ability based on MMP has been improved to take into account the features of the layout of WMV samples. Specifically, taking into account the different values of loads on the front axle of vehicles with hoodless and hood layouts at the same gross weight. In general, the improved procedure makes it possible to give a quantitative assessment of the movement mobility of WMV samples with various layout schemes and an assessment of their potential cross-country ability on the basis of the proposed refinement of MMP calculation
30 March 2020 in ACTA IMEKO
The ability to determine and control the normalized concentrations has been established using the experimentally obtained dependencies of the active and reactive constituents of conductivity in the wide frequency range of the electromagnetic field on the composition of the multicomponent fluid and the impurity concentrations. For high-aqueous substances dissolved in water (cooling liquids), a method for controlling the qualitative and quantitative composition is developed. It is based on the comparison of the measured and experimentally established active conductivity component and the comparison of the corresponding dependencies in the frequency field of the reactive component of conductivity. The developed electric method allows quantitative and qualitative estimation of the composition of the coolant on the contents of controlled components in the short time (up to 2 seconds) in a non-laboratory environment and to ensure uninterrupted operation of the equipment.
14 March 2022 in Journal of Water and Land Development
The impact of wind power plants on the environmental components is assessed taking into account a number of their parameters, in particular the technical characteristics of wind turbines, the characteristics of networks, engineering and other structures. To do this the life cycle of the wind power plants is described taking into account (by way of inventory) all the necessary materials and resources. Waste management scenarios have been developed, the use of which will make it possible to reduce the harmful impact on the environment. Based on the inventory and input data on the wind farm under study, a diagram is generated – a tree of life cycle processes of the wind power plant – to determine the potential environmental impacts. A list of impact categories that represent the load on the environment caused by the wind power plant is defined; also, the relative contribution of harmful factors is determined for each category, taking into account possible scenarios of waste management. Ecological profiles have been built for all potential impacts on the environment. After normalisation and determination of significance, individual estimates of all indicators and their distribution in three categories of lesions were obtained: human health, ecosystem quality and resources, as well as four stages of the wind farm life cycle: production, dismantling and disposal, operation, transportation and installation. The obtained profiles made it possible to determine individual indicators and eco-indicators, expressed in eco-points that characterise the wind farm under study.
4 January 2022 in PRZEGLĄD ELEKTROTECHNICZNY
The article discusses the issue of water quality improved by the metrological characteristics of the standard unit of ultrasound power in the aquatic environment by an automated control of the purification process. The received experimental results demonstrate that this new electric method of control is highly efficient
20 February 2023 in PRZEGLĄD ELEKTROTECHNICZNY
The article argues and describes a new approach to the technical assessment of the impact of military activity on surface water sources, which is based on new electrical indicators: Red-Ox, admittance; this will improve the processes of monitoring and responding to threats to the environment.