This experimental study deals with the heat transfer and friction effects of sinusoidal part turbulators for single-phase flows occurring in a circular shaped pipe. Turbulators with three different radius values are placed in the pipe to make the flow turbulent. In this way, changes in Nusselt number and friction coefficient are examined. As a result of the experiments made with Reynolds numbers in the range of 6614-20710, the increase rates of the Nusselt numbers of turbulators with 20 mm, 110 mm, and 220 mm radius compared to the empty pipe were obtained as 153.49%, 85.36%, and 52.09%, respectively. As a result of the decrease in the radius, there was an increase in the Nusselt number and the friction factor. Parallel to the Nusselt number, the highest friction factor was obtained in the smallest radius turbulator. It was found that the thermal enhancement factors of 110 mm and 220 mm radius turbulators increased by 179.54% and 132.95%, respectively, compared to the 20 mm radius turbulator. Similarly, it was determined that the thermal enhancement factor of the 110 mm radius turbulator increased by 20% compared to the 220 mm radius turbulator.
In this study, the effects of different numbers of sphere turbulators placed in a circular-shaped test pipe under turbulent flow conditions on heat transfer, friction factor, thermal performance factor and entropy production were experimentally investigated. Water was used as the working fluid in the experiments carried out in the number range Re = 8379-16701. Initially, plain pipe and supported plain pipe experiments were carried out by keeping the fluid inlet temperature and test pipe surface temperature constant. Then, 1, 2, and 3 sphere turbulator experiments were carried out under the same conditions, respectively. According to the findings, the maximum Nusselt number increase compared to the supported plain pipe was 83.34% for the test pipe with 3 sphere turbulators. The minimum and maximum Nu number increase rates of 3 sphere turbulators compared to 1 and 2 sphere turbulators were obtained as 42.61%-46.93% and 13.99%-17.11%, respectively. The increase rates of maximum friction factors of 1, 2, and 3 sphere turbulators compared to the supported plain pipe were 174.42%, 226.70%, and 306.53%, respectively. In addition, the maximum total entropy rate for sphere turbulators was obtained as 0.058 W/mK for 1 sphere turbulator at Re = 8379. In terms of the second law, the maximum entropy generation of sphere turbulators compared to the supported plain pipe decreased by 79.39% for 3 sphere turbulators at Re = 8379. As a result, it was concluded that the optimum number of sphere turbulators is 3 sphere turbulators with the lowest entropy production number and the highest thermal performance factor value (1.28).
1 January 2025 in Uludağ University Journal of The Faculty of Engineering
In this study, the effects of turbulators with different P ratios placed in a circular cross-section test pipe under turbulent flow conditions using water as the working fluid on heat transfer, friction factor (f), and entropy production were investigated using Ansys-Fluent 2021. The lowest Nu was calculated as 111 at Re=11825 for P=6, while the highest Nu was calculated as 219 at Re=19133 for P=1. The increase in Nu values for P = 6, 3, 2, 1.5, 1.2, and 1 compared to the plain pipe is 10.34%-11.64%; 17.39%-18.78%; 25.31%-26.56%; 34.42%-35.88%; 43.53%-44.87%; and 50.36%-51.47%, respectively. In turbulent situations, the highest entropy production rate was found to be 0.3631 W/mK at Re=11825 for P=6, while the lowest entropy production rate was found to be 0.2215 W/mK at Re=19133 for P=1. The minimum and maximum Ns reduction compared to the empty pipe was calculated as 7.13% for Re=19133 at P=6 and 46.62% for Re=11825 at P=1, respectively. In turbulent conditions, the highest Bejan number was found to be 0.9931 at Re=11825 for P=6. As a result, it was concluded that a ratio of P=1 provides maximum benefit in terms of heat transfer, while a ratio of P=6 is ideal in terms of total entropy production.
17 September 2026 in Journal of Thermal Analysis and Calorimetry