Tianlu Xu

Tianlu Xu

Auto-generated profile, based on publicly available information

Tianlu Xu

Key Laboratory of Automobile Materials

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
23 August 2018 in RSC Advances
Verified
Journal Article
Open access
PDF file
Lijie QuLijie Qu
Lijie Qu
CZChunling Zhang
Chunling Zhang
PLPeihong Li
Peihong Li
XDXueyan Dai
Xueyan Dai
TXTianlu Xu
Tianlu Xu
YDYanli Dou
Yanli Dou
Epoxy resin composites with improved thermal resistance and flame retardancy were fabricated based on P(H) microcapsules.

13 July 2018 in New Journal of Chemistry
Verified
Journal Article
Closed access
PDF file
TXTianlu Xu
Tianlu Xu
CZChunling Zhang
Chunling Zhang
PLPeihong Li
Peihong Li
XDXueyan Dai
Xueyan Dai
Lijie QuLijie Qu
Lijie Qu
YDYanli Dou
Yanli Dou
Polysiloxane foam (PSF) is a foam material with outstanding performance. However, the limiting oxygen index (LOI) of pure PSF is only 22.0 vol%, which can be attributed to combustible materials. In this work, graphene oxide (GO) was functionalized with hexachlorocyclotriphosphazene (HCCP) and 3-aminopropyltriethoxy-silane (APTS). The introduction of the functionalized GO into the PSF matrix has significantly improved the dispersion and flame-retardant properties of the final PSF composite. The char residue of PSF with 1.0 wt% functionalized GO content is 43.04%, which is considerably higher than that of the pure PSF (23.18%). Furthermore, the Tmax of PSF with 5.0 wt% functionalized GO content has increased from 585.9 °C to 668.8 °C. The results of the cone calorimetry test indicate that modification with functionalized GO prolongs the combustion of PSF composites. The LOI value of PSF with 5.0 wt% functionalized GO content has increased from 22.0% to 27.6%. In addition, the peak heat release rate, total heat release, and total smoke production of PSF with 5.0 wt% functionalized GO content were decreased by 49.2%, 14.5%, and 62.2% relative to those of pure PSF. These results can be ascribed to the barrier effect of GO, the condensed-phase and gas-phase mechanisms of HCCP, and the bonding effect of APTS.

18 March 2019 in New Journal of Chemistry
Verified
Journal Article
Closed access
PDF file
TXTianlu Xu
Tianlu Xu
JZJinrui Zhang
Jinrui Zhang
Lijie QuLijie Qu
Lijie Qu
XDXueyan Dai
Xueyan Dai
PLPeihong Li
Peihong Li
CZChunling Zhang
Chunling Zhang
A phenyl group was introduced into the polymeric network of polysiloxane foam for the improvement of its thermal insulation capacity and thermal stability. Phenyl-containing polysiloxane was prepared via ring-opening polymerization, and phenyl-containing polysiloxane foam was fabricated through simultaneous foaming and crosslinking reactions. With increasing phenyl content, the thermal conductivity of the polysiloxane foam decreased from 0.093 W m−1 K−1 to 0.079 W m−1 K−1. When the phenyl content was 6.15 mol%, the average cell diameter decreased from 384 μm to 165 μm and the cell density increased from 0.58 × 108 cells per cm3 to 4.67 × 108 cells per cm3. When the phenyl content was 8.5 mol%, the cell morphology became imperfect and the average cell diameter and cell density reached 259 μm and 1.29 × 108 cells per cm3, respectively. TGA results revealed the improved thermal stability of the polysiloxane foam. The TGA curves under nitrogen and air conditions could be divided into three stages. Under nitrogen conditions, the mass loss of the maximum decomposition stage decreased and the residue at 800 °C slightly increased. Under air conditions, the maximum decomposition temperatures of the three stages increased. The compressive strength and specific compressive strength were measured and showed a downward trend.